Answered: . If the pressure at a point is 1m of…

. If the pressure at a point is 1m of water, what will be it's value in terms of m of oil? (Take, the specific gravity of pil to be 0.8) a) 0.8 5) 1 =) 1.25 d) 2.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Panel AB is circular and retains a liquid with specific gravity of 1.6. It has a width of 4 feet…

Q: Determine the unit weight in kN/m³ of the fluid if at a point 6.58 m below the surface, the pressure…

Q: A = 1000 mm a = 40 mm² h, = 500mm h, = 300mm 1000x 20 500 log 10 300 K = 2.303- 40 x180 K = 1.42…

A: Given- cross-section area of the soil mass A=1000 mm2area of stand pipe a=40 mm2Length of the soil…

Q: Analyze the figure below and determine the absolute pressure in the tank. Take the density of water…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Calculate the draft or depth of submergence of a wooden block having a width of 3.5m, depth of 1m…

A: Given data in question Length 7 m Width 3.5 m Depth 1 m Density 850 kg/m3 To find out Depth of…

Q: Determine the value of h in an open tube piezometer attached at the bottom of the tank and the…

A: Given Pressure at A,PA=87N/m^2 Density of water=1050 kg/m^3

Q: A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: 1. The gage pressure of the air in the tank shown in the figure below is measured to be 65 kPa.…

Q: Container has some fluid as shown in figure if container is moving with uniform velocity 10 m/s,…

A: Uniform velocity of container V=10 m/s, Pressures- PabsA=130 kPa&Patm=100 kPa. To Find- The…

Q: ds oil as shown. The contact between the cylinder and the wall is smooth. Consider a 2- m length of…

Q: Atmospheric pressure is used to lift a part with a surface area of 0.008m^2. The piece is placed in…

Q: 6m hi 2.3m 6m dos 300mm 2m 3m 2m 45 45 6m 1.

A: Given Data ; tank 1 diameter = 6 m tank 2 dimension = (3m , 2m) water level diffrence = 2.3 m H1=…

Q: A hydraulic jack contains 2.0 litres of oil as the working fluid. The compressibility of the oil is…

A: Given, Volume of oil(V) = 2ltr=2×10^-3 m^ compressibility (B)= 1.98×10^-10/pa Pressure (p)…

Q: Q3. A solid half cylinder with 3 m height and radius of 0.5 m floats in water with a 0.5 m thick oil…

A: When a body is either fully or partially immersed into any fluid, the hydrostatic lift due to net…

Q: Please

Q: The cylinder shown in the figure extends 9 ft into the paper. If the cylinder has the radius of 4…

Q: 6 Determine the absolute pressure at C in kPa if the atmospheric pressure is 101.325 kPa. * 105.525…

A: Figure is as shown

Q: ,it expanded át čóńštánt Calculate the work done,

Q: Two spherical vessels of different sizes contain the same gas and are connected by means of a pipe…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the 4, 5 and 6. Please resubmit the…

Q: (b) Fill the Principal SI Unit as shown in Table Q1. Table Q1 Unit Meter per second square Quantity…

Q: Find the specific gravity of the material. b. How much weight is required to fully submerge the…

A: Given data: side = 4 in SG = 0.82

Q: In which fluid will a pressure of 680 kPa fırst be achieved? Po = 90 kPa ethyl alcohol p = 773.3…

Q: PROBLEM 4: The tank contains a liquid having a density as shown. 0.82 ft 10 ft 5 ft 7 ft Pliquid =…

A: (a) multiplying the density by "g" acceleration due to gravity to obtain the unit weight Unit…

Q: A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The…

Q: A propped cantilever beam (fixed at one end and simply supported at the other end) has a span L of…

A: As Per Bartleby guidlines in case of multiple questions, I have provided the solution of first…

Q: 1200 psi. Compute for the stress c

Q: To measure a baseline a steel tape 30m long standardized at 15° with a pull of 80N was used. Find…

Q: A vertical wall shown in the figure is 20 meters wide. Determine the height, h, of the oil in the…

Q: (b) Convert 100 kPa to psi. You may need to use the following estimates: 1 lbf = 4.45 N, 1 ft = 12…

Q: 12. The uniform bar and the homogeneous cylinder eac equilibrium, calculate the normal and friction…

Q: 11. If the pressure at a point is 1m of water, what will be it's value in terms of m of oil? (Take,…

Q: 5. If the pressure in a tank of oil (sp gr 0.85) is 3yx kN/m2, what is the equivalent head (a) in…

Q: PROBLEM 1. The Bulk Modulus of 1 kg of water is 2.2 GPa. If the percentage reduction in volume is…

A: Given:- m=1kg K=2.2GPa percentage reduction involume=6% To find:- Pressure

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

If the pressure at a point is 1m of water, what will be it's value in terms of m of oil? (Take, the specific gravity of
oil to be 0.8)
a) 0.8
b) 1
c) 1.25
d) 2.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cylinder shown in the figure extends 11 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85) 4 ft 50
Quiz 1. If in figure, the pressure at m is 20 Ib per sq.in., what is the corresponding pressure at n when z = 8 in? oil (sg. = 0.80) m water 4"
The pressure read on the pressure gauge of the system in the figure is 65 kpa. Considering the data shown, determine the height difference "h" on the differential pressure gauge. Aire = air Agua = water Aceite = oil Mercurio = mercury
The cylinder shown in the figure extends 10 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil ( s.g. = 0.85 ) 4 ft 0, 50
A cylindrical barrier holds oil as shown. The contact between the cylinder and the wall is smooth. Consider a 2- Im length of the cylinder. The water inside the cylinder is exposed to atmospheric pressure. What is the minimum mass (ton) to achieve the equilibrium as shown in the figure? B Oil S.G. =0.8 r=m 57 Water
2
i need the answer quickly
Q 1 A
The water tank has a diameter of 750mm , a height of 1750mm to which the Initial height of water was 5 cm. If water was to be filled 90% of height and the water meter initial reading is 2000L, a. what is the final reading of the water in L b. Find the mass of water tank if its initial weight is 45 kg
9 2 10 GU Terr Question 2 Refer to the given figure below. Given: a = 1.55 m b = 1.11 m c = 0.73 m Carbon Tetrachloride, sg = 1.60 b B Carbon tetrachloride Water Determine the pressure difference (kPa) between points A and B. Express your answer in 2 decimal places. Neglect sign. |-0- Cip