Sociology Assignment 5

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

I need help solving this problem.

Stuck need help! Problem is attached. please view attachment before answering.  Really struggling with this concept. Please show all work so I can better understand ! Thank you so much.

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.  You must follow the following steps to help the team:  STEP 1  Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:  The input and output heat and net output work The expansion and compression strokes The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work. STEP 2  Explain the mechanical…

Problem 2: Review the below link, and choose 3 practical examples to solve structural/performance-based issues using finite element product. Discuss what you understand from these examples. Use your own words. https://www.hitechfea.com/fea-projects.html hitech Since Your Partner in Digital Excellence 1992 SERVICES ✓ PROJECTS ✓ » FEA Projects CLIENTS FEA shortens the Design Cycle for Thermal Radiation Detector System for Power Plant BLOG ABOUT US CONTACT US Finite Element Analysis - FEA Projects / Case Studies Please review few of the FEA projects, FEA case studies and FEA work samples that represent the FEA solutions HiTech FEA engineers have provided to our global clientele from different industries. Simulation using ANSYS Professional NLS helps to reduce Product Development Cycle Effective Static Structural Services conducting Structural Seismic Analysis of RTO System Base

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

Please solve, engineering econ

Hello, so i have attached two images. the first image is the quetions, i need part b) answered if possible. i have attached my findings to part a) to add to the little information we know to help with part b if needed. Thnks

Direction: Graph the heating curve of ethanol using the information given. Check off each item as you add additional information to your graph so that none is missed.  Background information of Ethanol: Boiling Point = 78 0C Melting Point = -114 0C Starting Temperature = -120 0C After two minutes, frozen cold ethanol starts to melt. It takes two minutes to melt completely. After eight more minutes, it begins to boil. It boils for six minutes. Heat is added for two more minutes until ethanol reaches 80 0C. Label “melting” where this takes place. Label “vaporization” where this takes place. Label “phase change” where a phase change occurs. Indicate where ethanol is only a SOLID, only a LIQUID, and only a GAS. Of the three phases, label which phase has: weakest IMF, strongest IMF, and medium IMF.

Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…

Chrome File Edit View History Bookmarks People Tab Window Help McGraw-Hill Campus - ALEKS Science - CHM1045 GEN CHEM 1 BLENDED 669113 A bconline.broward.edu/d21/le/content/466883/fullscreen/12868783/View McGraw-Hill Campus - ALEKS Science O GASES Interconverting pressure and force A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 470.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 2.80 MN. pressure vessel bolts side View port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. O cm Explanation Check O2021 McGraw-Hill Education. All Rights Reserved. Terms of Use FEB

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

dear tutor please provide neat and clean and detailed answer. dont copy from google adress both questions well

Please write solution on paper, thank you. No typing, it's hard to follow. I''l give positive feedback.

Part 1: Suppose that our company performs DNA analysis for a law enforcement agency. We currently have 1 machine that are essential to performing the analysis. When an analysis is performed, the machine is in use for half of the day. Thus, each machine of this type can perform at most two DNA analyses per day. Based on past experience, the distribution of analyses needing to be performed on any given day are as follows: (Fill in the table)   Part2: We are considering purchasing a second machine. For each analysis that the machine is in use, we profit 1400$. What is the YEARLY expected value of this new machine ( ASSUME 365 days per year - no weekends or holidays