EET231L_HeatTreat Machine_ZacharyTrotter

University of Babylon Collage of Engineering/ Al-Musayab Department of Automobiles Final Examination/ Stage: 3rd Notes: Answer 4 questions only 2023-2202 Subject: Theory of vehicles Date: 2023\06\10-Saturday Time: Three Hours Course 2nd Attempt 1st Q1: A Hooke's coupling connects two shafts whose axes are inclined at 30°. The of the driven shaft? Find the maximum value of retardation or acceleration and driving shaft rotates uniformly at 600 rpm. What are the extreme angular velocities state the angle where both will occur. (12.5 Marks) Q2: Four masses, A, B, C, and D), revolve at equal radii and are equally spaced along a shaft. The mass B is 7 kg, and the radius of C and D make angles of 90° and 240°, respectively, with the radius of B. Find the magnitude of the masses A, C, and D and the angular position of A so that the system may be completely balanced. (12.5 Marks) Q3: A cam has straight worked faces that are tangential to a base circle of diameter 90 mm. The follower is a roller…

Help!!! Please answer all Correctly!!! Please

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Help!!! Please answer part B correctly!!! Please

University of Babylon Collage of Engineering/ Al-Musayab Department of Automobiles Mid Examination/ Stage: 3rd Subject: Theory of Vehicles Date: 14 \ 4 \2025 Time: 1.5 Hours 2025-2024 Q1: The arms of a Porter governor are 250 mm long. The upper arms are pivoted on the axis of revolution, but the lower arms are attached to a sleeve at a distance of 50 mm from the axis of rotation. The weight on the sleeve is 600 N and the weight of each ball is 80 N. Determine the equilibrium speed when the radius of rotation of the balls is 150 mm. If the friction is equivalent to a load of 25 N at the sleeve, determine the range of speed for this position. Q2: In a loaded Proell governor shown in Figure below each ball weighs 3 kg and the central sleeve weighs 25 kg. The arms are of 200 mm length and pivoted about axis displaced from the central axis of rotation by 38.5 mm, y=238 mm, x=303.5 mm, CE 85 mm, MD 142.5 mm. Determine the equilibrium speed. Fe mg E M 2 Q3: In a spring loaded Hartnell type…

Please do not copy other's work and do not use ChatGPT or Gpt4,i will be very very very appreciate!!! Thanks a lot!!!!!

Please solve, engineering econ

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

as per your policy, customer service from bartley stated since you took a incomplete question and answered it instead of questions that actually need answering.    you owe me my questions and not to only solve one question, kindly solve all 3. And when i end up switching to CHEG not only will i be posting this on my vlog and social media i will also be contacting BBB and i will make sure to find out whos the special kid behind answering and trolling me ((:   kindly answer all 3 , thanks

Help!!! Please answer part B correctly!!! Please

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores ■Review Next >

2. In studying for your CBEMS 125B exam, you get hungry and decide to boil some water in a pot to make instant noodles. You put your aluminum spoon, with a long handle (i.e. good to use "long fin approximation"), in the pot in anticipation of stirring the noodles into the boiling water. However, your phone rings, and you leave the spoon in the boiling water on the stove for quite a while (i.e. the system reaches steady-state conditions) before you come back to it. The boiling water is at 100°C and room temperature is 25°C. The spoon has a square handle that is 0.6 cm per side. At a handle height of 8 cm, the temperature of the long aluminum spoon is 62°C. The Royal Society for the Prevention of Accidents lists a maximum surface temperature of 58°C as a "safe" touchable temperature for metals. Is the spoon safe to pick up at a handle height of 12 cm? Justify your answer with calculations. Assume (1) No radiation effect, (2) convection heat transfer coefficient is uniform in the pot…

The following is a series of questions pertaining to the NSPE Code of Ethics. Please indicate whether the statements are true or false. These questions are provided by the NSPE. Note: This ethics test is intended solely to test individual knowledge of the specific language contained in the NSPE Code of Ethics and is not intended to measure individual knowledge of engineering ethics or the ethics of individual engineers or engineering students. Engineers may issue subjective and partial statements if such statements are in writing and consistent with the best interests of their employer, client or the public.

1. Please help me solve this mech. engineering question

I want to briefly summarize what he is talking about and what you conclude. pls very urgent

Quastions about renewable

You are an engineer in a company that manufactures and designs several mechanical devices, and your manager asked you to help your customers. In this time, you have two customers, one of them wants to ask about internal combustion engines while the other requires a heat exchanger with particular specifications. Follow the parts in the following tasks to do your job and support your customers.Task 1:Your first customer asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report which includes the following steps:STEP 1Describe with the aid of diagrams the operational sequence of four stroke spark ignition and four stroke compression ignition engines.STEP 2Explain and compare the mechanical efficiency of two and four-stroke engines.STEP 3Review the efficiency of ideal heat engines operating on the Otto and Diesel…

Help!!! Please answer part b correctly like part A. Please!!!!

Help.