Quiz 3

Assignment 1: TIME VALUE OF MONEY Objective: To further understand the concept of the time value of money. INSTRUCTIONS: In each problem, a. Translate data given in problems into their respective graphical representations - i.e. draw the correct cash flow diagram. b. Write down all pertinent given information or data on your paper. c. Calculate answers correctly. 3. A certain college graduate, Sallie Evans, has $24,000 in student-loan debt at the end of her college career. The interest rate on this debt is 0.75% per month. If monthly payments on this loan are $432.61, how many months will it take for Sallie to repay the entire loan?

TOPIC: ENGINEERING ECONOMICS SPECIFIC INSTRUCTION: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOX your final answers. Express all your answers in 2 decimal places. PROBLEM: Cardinal Financing lent an engineering company Php 500,000 to retrofit an environmentally unfriendly building. The loan is for 5 years at 10 % per year simple interest. How much money will the firm repay at the end of 5 years?

This is the complete question and not a writing assignment. Make sure for this problem you list the following: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an appropriate number of significant figures.

Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?

Group Problem: You are planning to build a log cabin in Northern Minnesota on a remote hill with a beautiful view of the setting sun. You will drag the logs up a long sometimes rocky hill to the building site by means of a rope attached to a winch. You will need a rope for this job so you aim to know how much weight the rope would safely support. You are operating on a tight budget so matching the rope strength would be a cost saver. You know that the logs are heavy, and estimate the heaviest as 1,000 lbs. From maps you verify the hill is steeped at an angle of = 70° with respect to the vertical, and you estimate a coefficient of kinetic friction between a log and the earthen hill as 0.5. When pulling a log you will ensure that the uphill acceleration is never more than 3.0 ft/s². The maximum recommended load is th of the nominal strength for the ropes considered as stated on the product labels, you have three ropes in mind: 12 kN, 18 kN, & 24 kN. Which one of these three rope…

Case Study: Paula’s Pain Paula has worked for Brindle Corporation for 3 years.  During this time, she has worked as a machine operator/cell leader in various work cells.  Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel.  These tubes get a hole punched in them, a flange welded on, and burrs ground off.  The pipe then gets placed into a gage to check that it was made correctly.  (The tubes weigh about six pounds.) Paula has been performing the welding operation.  She leans into the machine and loads the part into a fixture then positions the flange.  Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position…

operations research -  pert cpm

This is an engineering problem and not a writing assignment. Please Do Not Reject. I had other engineering tutors on bartleby help me with problems similar to this one. This problem must be presented in a logical order showing the necessary steps used to arrive at an answer. Each homework problem should have the following items unless otherwise stated in the problem: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. Most sources will be from a table in the textbook (i.e. Table A-4). e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an…

Requirement show your working

Please Use excel Shee t Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.

Can you please answer the questions below

LESSON: AUTODESK AUTOCAD Choose from the choices:

all one question help asap please!

5 Look at the flow chart showing the steps of the design process. Then read the list of steps for designing a thermos. These steps are not in order. Write the letter of each step in the appropriate box of the flow chart. The Design Process Find a problem Keep records Plan and build a prototype Keep records Test and improve Keep records Communicate the solution

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Please answer the 4th question