HW2

(General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single lines to show piping and electrical wires. The parts and components are shown by symbols. A. Diagram Assembly Drawings B. Altered Item Drawings C. Modified Item Drawing D. Dimensioned drawing 2. Balloons are shown on assembly drawings to reference parts to the ___________.  A. Title Block B. Revision Block C. Parts List D. Supplemental B   3.   ____________use conventional symbols with single lines to show piping and electrical wires. The parts and components are shown by symbols. A. Diagram Assembly Drawings B. Altered Item Drawings C. Modified Item Drawing D. Dimensioned drawing

Need help with this question. A bit urgently if possible

A robot is used for loading and unloading of parts to automated flexible machines. Loading time is 1 minute; unloading time is 1.5 minutes; machining time 15 minutes; Robot travel time between the machines including the inspection time is 3 minutes. Cost of robot C,=30 TL/Hour; cost of machines C2=40 TL/Hour. How many machines (integer number) should be assigned to the robot so that the total robot and machine costs per cycle are minimized? 8 - 176 a) 4 b) 3 c) 2 d) e) 6.

I can't find the symbols for the blank ones

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…

Can someone please help to solve all of the following problem showing all work and include a load chart. Thank you!

intake valve v) vi) intake compression How Tuel injector power lo egiteqo190 the number of molecules in the cylinder the internal energy of the gas; the work done on or by the gas; the thermal energy exchanged with the environment. exnaust vaive The diagrams show the cylinder of a petrol engine in 4 stages. Petrol vapour and air are drawn into the cylinder, The mixture is then squeezed together, and then exploded by a spark. The explosion pushes down the piston. The exhaust gases are then expelled from the cylinder. pril Use the first law of thermodynamics to analyse the energy changes during the process. At each stage explain what happens to the gas exhaust 0101

I need help answering these two parts pertaining to the print provided below.   For this drawing, are there other views besides View E-E and View F-F? If so, where are they? (Multiple Choice)a. No, the drawing has no additional viewsb. Yes, but they are very smallc. Yes, but they're only found on the CAD systemd. Yes, on other sheets What is the current revision status of this print? (Multiple Choice)ABCD

I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing

answer the following BOTH questions, and i know the policy, the 2 questions is FINE and i have read the policy, thanks