MODULE 1 QUIZ REVIEW

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

A,B,C please

please hand written solution  please hand written solution  please hand written solution

Industry Print Exercise 23-2 Refer to print PR 23-2. The sequence of operations for this print is given below. Answer the questions following the sequence of operations. Sequence of Operations descends at a controlled rate, slowly compacting the explosive charge to avoid detonation due to a sudden Description: This is a system to control a 90-ton hydraulic, explosive-compaction press. The press ram shock. 1. The cycle is started by energizing solenoid A, which shifts control valve 3 and supplies pressure to the head end of the hydraulic cylinder (7). This operates the ram. 2. The cylinder (7) extends at a slow rate controlled by the fluid in the rod end of the cylinder, which is vented through the flow control valve (5). the 1. When de-energizes solenoid A and energizes solenoid B. This shifts control valve 3 to retract the cylinder (7). de rol valve 5 has an integral check valve that permits the free flow of fluid in the opposite direction, causing the cylinder (7) to rapidly retra…

Needs Complete typed solution with 100 % accuracy.

I can't find the symbols for the blank ones

i need the answer quickly

1. What company specification number is given to the material for this part?  2. What is the revision letter (issue) for this print? 3. Is this a monodetail or multidetail part? so close to being done pls help

I need answers to parts 4, 5, and 6, pertaining to the print provided.

A symbol used to identify a physical feature of a part as a datum feature is called a: O Reference feature O Feature control frame Feature of size O Datum feature symbol

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5.  1 pass 2 fail 3 fail 4 pass

Name Section 5-2: Line Diagrams-Signals, Decisions, and Actions In the following application, a temperature switch controls a heating contactor and a flow switch is used to ensure there is enough air flow. If there is not enough air flow, an alarm is sounded. Complete the required information. 1. List all the signal devices in the circuit. 2. List all the action devices in the circuit. 3. List the decision part of the circuit that automatically sounds the alarm if there is a problem. 4. When the heating element is on during normal operation, is the flow switch open or closed? CIRCULATING 2 L1 FAN TEMPERATURE SWITCH TR HEATING ELEMENTS FLOW SWITCH -HOT AIR PADDLE AIR FILTER NORMALLY CLOSED FLOW SWITCH 65 ALARM (SOUNDS IF NO FLOW FOR 15 SECONDS OR MORE) Date HEATING CONTACTOR TR ON-DELAY TIMER SUPPLY AIR COLD AIR (3) TIME SET= 15 SEC © 2014 American Technical Publishers, Inc. All rights reserved

An emergency stop system is to be designed for a certain automatic production machine. A single “start” button is used to turn on the power to the machine at the beginning of the day. In addition, there are two “stop” buttons located at two locations on the machine, either of which can be pressed to immediately turn off power to the machine. Let X1 = start button (normally open), X2 = stop button 1 (normally closed), X3 = stop button 2 (normally closed), and Y = power-to-machine. (a) Construct the truth table for this system. (b) Write the Boolean logic expression for the system. (c) Construct the ladder logic diagram for the system

Answer questions 1 and 3 and 5 in full detail please

4

Given the removal and replacement time data in the table, calculate IMART (mean time to repair) Part identity Bolts Earth strap Power lead Signal lead Cover plate Brushes Lesson 1.2 HW#1 Quantity Failure rate x 10-4 (h) Total M task time (h) 3 0.20 1 0.10 0.36 0.10 0.26 0.35 2 0.46 0.12 0.36 1.16 1.05 23.6

Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along with Figure 4 shown below, which parts in Figure 4 would now 'pass' inspection?   figure 4 has been attached and figure 5 for reference

I have three parts that need to be answered pertaining to the print provided below.   With respect to the part of subassembly 1 that attaches to subassembly 2, which word bestdescribes the shape of the material at the connection: round tube, hexagon tube, squaretube. (Multiple Choice)A: round tubeB: hexagon tubeC: square The top assembly featured in this drawing appears to have two tall stems, each about 14.5″tall. What relationship exists between the two axes of the stems? (Multiple Choice)A: PerpendicularB: ParallelC: AngledD: X shaped When looking at Section A-A, how does the print reader know that this is several parts or pieces and not just one part? (Multiple Choice)A: Section lines are at different anglesB: The title block has the European symbolC: There's a general note that reads 'section shows more than one part'D: The reader must assume its several parts

-50- No elements selected A (-20,-40) -40- -30- R=64 (5,0) ,ksi -50 -40 -30 -20 -10 10 20 30 40 50 10 20- 30- 40- 50+t, ksi 20 ksi Press TAB to navigate between elements on the canvas. Press ALT+M to get to the main menu. Press ALT+A to modify the attributes. Press (ALT+Q) to quit the application. 30 ksi Submit Previous Answers Request Answer 40 ksi X Incorrect; Try Again; 2 attempts remaining