Alcala-using_directional_terms

I need parts 3 and 4 answered pertaining to the print provided.  I asked this question previously on here and I received the wrong answers to the 2 parts Im asking about, so I am reposting the question again to have another tutor answer it.   Part 3: I need to tell what was ommited. Part 4: I need to tell what the triangle equals? Lower right or J1 zone has the answer.

I need help solving problems 7, 8, and 9 pertaining to the print attached below.

Please Full answer and make sure to use the formulas provided and draw the sketches. Make sure to write all the units in the steps, please Handwriting CLEAR & BIG, please Please please no copy from other answers , need new correct one with all steps, please

Don't use chatgpt will upvote

I need the answers to this part, I have submitted this question twice on this site and both times received way different answers...as I am unsure which tutor to listen to, I am uploading this question for the third time and I am asking a very highly knowledgable tutor to help me solve this. If you are uncertain, please leave it for another tutor.

Oz Lawn Care Inc. manufactures and assembles lawnmowers that are shipped to dealers throughout the United States and Canada. Two different procedures have been proposed for mounting the engine on the frame of the lawnmower. PB (Minutes) UPB (Minutes )345798632 5 Is there a difference in the methods' mean time to mount the engines on the frames of the lawnmowers? The answer must be in handwriting. Please write your answer using a ball - point pen on plain paper. Submit your homework by uploading it to the canvas. Good Luck!

PLEASE: Can you write out the answers. Typing it out doesn't make sense all together

Hi, I need help with the first part of the problem below because I'm very confused about how P1 and P2 should be calculated. If you look at my notes to solve the problem there is already a formula in place as I always thought the Patm should also be multiplied by the Area in the numerator, but it's not if I look at this specific tutorial solution given by my course but it's not explained why. I have done a while ago a very similar problem with using that formula in my notes and it gave me the right results, but it's not working for this one. Could you please help me understand why as I have a test coming soon? Figure Q3 (see image attached) shows a cylinder and pistonenclosing air, the movement of the pistonbeing restrained by a compression spring ofstiffness 20 kN/m. The air is heated andexpands, the piston moving 0.3 m. Thefree length of the spring is 1.0 m.Calculate the work done by the air duringthe process.If the pressure , volume and internal energyof air are related by the…

Please walk me through finding how much force the women need to pull the force.

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5.  1 pass 2 fail 3 fail 4 pass

I think instantaneous velocity is less than 0 at d,e,f (negative slope) Need help how to find instantaneous acceleration

I need these three parts answered (Multiple Choice). If you can not answer all three parts, please leave it for another tutor to answer. Thank you.   What size paper was used for the original version of this print? (Multiple Choice)ABCD The two views near the bottom of the print are called detail views. Which one of theviews above (left side, front, or right side) shows the same geometry, but at the normal 1:1scale? (Multiple Choice)a. left sideb. frontc. right side What size paper was used for the original version of this print? (Multiple Choice)ABCD The two views near the bottom of the print are called detail views. Which one of theviews above (left side, front, or right side) shows the same geometry, but at the normal 1:1scale? (Multiple Choice)a. left sideb. frontc. right side The major diameter (100 mm) of this part is interrupted by a flat surface on top. Is an auxiliary view required to show the true size and shape of that flat surface? (Multiple Choice)a. Yesb. No

I need the answers to this part, I have submitted this question three times on this site and all three times received way different answers...as I am unsure which tutor to listen to, I am uploading this question for the third time and I am asking a very highly knowledgable tutor to help me solve this. If you are uncertain, please leave it for another tutor.

I need problems 1, 2, and 3 solved pertaining to the print provided below.

I need answers with clear hand writing or using Microsoft word . ASAP   measurements , describe how to read the values given on the measurement tools and to write about measurement tools note: i want a lot of information

The answer is one of the options below please solve carefully and circle the correct option Please write clear .

I need help answering questions 7, 8, and 9 pertaining to the print attached.

I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave it for another tutor to answer. Thank you.   What size paper was used for the original version of this print? (Multiple Choice)ABCD The two views near the bottom of the print are called detail views. Which one of theviews above (left side, front, or right side) shows the same geometry, but at the normal 1:1scale? (Multiple Choice)a. left sideb. frontc. right side The major diameter (100 mm) of this part is interrupted by a flat surface on top. Is an auxiliary view required to show the true size and shape of that flat surface? (Multiple Choice)a. Yesb. No

I pay for professionals monthly to help with my homework questions and every question I’ve asked for the last two weeks have been rejected. Honestly just trying to psd this class so I can retake after I learn the basics. This is supposed to be introduction to engineering and it’s definitely exceeding introduction. Could I please get some assistance drawing this problem?

Pls answer correctly and corresponding to what is given in the image attached. The instructions are already in the image. Thank you

I have two parts that need to be answered (Multiple Choice). If you can not answer both parts, please leave it for another tutor to answer. Thank you.   On the left side view of this print, there is a horizontal, straight-line segment that does not connect to other lines. In basic terms, explain why. (Multiple Choice)A: It represents a rounded edge and is there to help clarify the view, even though no sharp edge exists.B: It represents a straight edge that can't be seen in other views.C: It's a drafting mistake and should not be there.D: It represents a locating edge on the part and must be there to establish a primary plane for the inspection setup. This print does not show a cutting-plane line. Is this acceptable practice or an error? (Multiple Choice)A: AcceptableB: Error

Please answer question with as much detail as possible Please Use the “NCEES FE Reference Handbook 10.0.1” which can be downloaded for Free from https://ncees.org/ as your Reference for tables and formulas

I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor. Thank you.   Many companies have a symbol, used much like an asterisk, that points out critical dimensions. How many critical dimensions are specified on this print? (Multiple Choice)a. fourb. fivec. sixd. eight For the dimensions, does this print use the aligned method or unidirectional method? (Multiple Choice)a. alignedb. unidirectional