Screenshot 2023-12-16 at 2.51.34 PM

For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?

The answer from Bartleby is missing/blank. Can someone help answer it please and credit this question if possible since it would have been included/explained? Thank you Chapter 50 multiple Choice #5 what is the cause of an extremely hard brake pedal

1. What company specification number is given to the material for this part?  2. What is the revision letter (issue) for this print? 3. Is this a monodetail or multidetail part? so close to being done pls help

A certain type of ship has two tanks in its engine. Each tank contains a different type of fuel. when the engine turns on, the same amount of energy is transferred out of both fuels. why did fuel 1 change pahse, but fuel 2 stayed the same. what happened to molecules of both fuels

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Summary: A car part manufacturing company currently produces a suspension assembly for Toyota Motor Corporation. Figure 1 shows the breakdown structure of the suspension assembly and Figure 2 shows the final assembly and how to fit into a car. Table 1 shows the name of components, part numbers, and the number of components in each suspension assembly.   Table 1. Part lists for Suspension Assembly Number in Figure 1 Part number Part name Amount per assembly 1 PA-T15-001 Shock absorber unit 1 2 PA-T15-002 Lower insulator 1 3 PA-T15-003 Spring bumper 1 4 PA-T15-004 Coil spring 1 5 PA-T15-005 Upper insulator 1 6 PA-T15-006 Spring upper seat 1 7 PA-T15-007 Bushing 1 8 PA-T15-008 Suspension Support 1 9 PA-T15-009 Washer 1 10 PA-T15-010 Stop nut 1 11 GE-001 Bolt 2 12 GE-002 Nut 5 Coil springs are produced in-house. The process to produce the coil spring in the company is as follows. (a) Heating the wire: to an appropriate temperature for the winding process. (b)…

Show work Part 1 website: https://ophysics.com/r5.html PArt 2 website: https://ophysics.com/r3.html

Hello, so i have attached two images. the first image is the quetions, i need part b) answered if possible. i have attached my findings to part a) to add to the little information we know to help with part b if needed. Thnks

University Of Babylon College of Mussayb Automobile Production Quiz(2) 2024-205 7. Which classification method considers the number of independent movements a robot can make? 0 0 о a) Classification by Degrees of Freedom b) Classification by Kinematic Structure c) Classification by Drive Technology d) Classification by Workspace Geometry 8. Which classification method focuses on the arrangement of the robot's joints? 。 a) Classification by Degrees of Freedom 。 b) Classification by Kinematic Structure ° c) Classification by Drive Technology od) Classification by Motion Characteristics 9. What is the difference between a robot with 2 Degrees of Freedom (DOF) and one with 6 DOF? о a) The 6 DOF robot can move faster. o b) The 6 DOF robot can move more precisely. o c) The 6 DOF robot can perform more complex tasks. o d) All of the above 10. What are some examples of drive technologies used in robots? 。 a) Hydraulic, pneumatic, and electric о b) Gear, belt, and chain drives o c) Ball screws,…

Could you please explain where and what is tight side and also how to find 5-9

1. In the operation of an internal combustion engine, the combustion gases expand in volume to make thepiston move. As this occurs ___________ gas particles move in the same direction as the motion of thepiston. Select the most correct phrase to go into this blank from these choices: A all theB almost all of theC very few of theD about half of the 3. What does the Second Law of Thermodynamics say about how much work can be done by a heat engine?Answer this in terms of either the heat added to the engine (Qh) or the heat expelled by the engine (Qc).

I need answers to questions 4, 5, and 6 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

Answer this for me mate. Much appreciated.

I REPEAT!!!!! I NEED HANDDRAWING!!!!! NOT A USELESS EXPLANATION!!!! I REPEAT SUBMIT A HANDDRAWING IF YOU CANNOT UNDERSTAND THIS SKIP IT !  I need the real handdrawing complete it by adding these :  Pneumatic Valves Each linear actuator must be controlled by a directional control valve (DCV) (e.g., 5/2 or 4/2 valve). The bi-directional motor requires a reversible valve to change rotation direction. Pressure Regulators & Air Supply Include two pressure regulators as per the assignment requirement. Show the main compressed air supply line connecting all components. Limit Switches & Safety Features Attach limit switches to each actuator to detect positions. Implement a two-handed push-button safety system to control actuator movement. Connections Between Components Draw air supply lines linking the compressor, valves, and actuators. Clearly label all inputs and outputs for better understanding.

The answer is one of the options below please solve carefully and circle the correct option Please write clear .

Subject : engineering design - DFMA

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

2. Summarize chassis configuration and adjustments for race cars emphasizing the data from the tables below:

3. Please help me solve all parts to this mech. engineering question

1. How will the date code be applied to the assembly? 2. What paper size is the original version of the print? 3. What is the scale of the original drawing? Thank you, ill be posting more if you are good with engineering please check again soon.

Which of these statements are correct?

answer a & b. Please show all your work!!