Screenshot 2023-12-16 at 3.01.45 PM

I need help with simulink. It is my first time using simulink. I am trying to make a simulink program turning on the LED on the board for 10sec for an Arduino Mega 2560. I have attached an image of what I tried to do. After I run, it just says no diagnostic. How do I know if I did this correctly or not?

13. User tool frame UT[3] was set up by the programmer with three-point method for UT setup provided by FANỤC robot system. Which of the following statements is correct. (a) UT[3] frame is measured relative to UF[h] frame. (b) The orientation of UT[3] frame is the same as the orientation of default TCP frame (i.e. Def- TCP frame). (c) The origin of UT[3] frame is exactly aligned to the origin of default Def-TCP frame. 14. Using three-point method for user tool frame UT[k] setup, a robot programmer can set up the user- defined of UT[k] for an end-effector. (a) position (i.e. origin) (b) orientation (c) position (i.e. origin) and orientation

21. The programmer uses three-point method for UT[2] setup for a sharp-tip pointer. If the programmer recorded each of three-points by precisely contacting the sharp-tip to the tip of the stationary reference pointer on the table, then (a) UT[2] setup is accurate (b) UT[2] setup is not accurate (c) the accuracy of UT[2] setup is still uncertain 22. User frame UF[3] is accurately set up on the part reference surface which is unparallel to the surface where the robot is mounted. To jog the robot TCP to move perpendicularly to the part reference surface, the programmer (a) needs to select World jogging coordinate system (b) needs to activate UF[3] and select User Frame jogging coordinate system

AutoSave STATICS - Protected View• Saved to this PC - O Search (Alt+Q) Off ERIKA JOY DAILEG EJ File Home Insert Draw Design Layout References Mailings Review View Help Acrobat O Comments E Share PROTECTED VIEW Be careful-files from the Internet can contain viruses. Unless you need to edit, it's safer to stay in Protected View. Enable Editing Situation 9 - A 6-m long ladder weighing 600 N is shown in the Figure. It is required to determine the horizontal for P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. 25. Determine the reaction at A. 26. Determine the reaction at B. 27. Determine the required force P. 4.5 m 1.5 m H=0.2 30° Page 5 of 5 671 words D. Focus 100% C ЕPIC GAMES ENG 7:24 pm w US 16/02/2022 IZ

Please examine how you got answer step by step please

Part III Capstone Problem Interactive Physics - [Lab7Part3.IP] Eile Edit World View Object Define Measure Script Window Help Run StoplI Reset 圖|& 品凸? Time Length of Spring 22 6.00 dx Center of Mass of Rectangle 2 5.000 Tension of Rope 3 Jain@ IFI ... N ot rot ***lad Split 4.000 Velocity of Center of Mass of Rectangle 2 Vx Vx V Vy MM Ve - m/s m/s 3.00 *** m/s Vo ..* lad/s 2 00 Center of Mass of Rectangle 1 1.000 tol rot *.* rad EVelocity of Center of Mass of Rectangle 1 Vx Vx VVy M 0.000 -m/s w 30 m/s w.. MI Ve 母100 *** m/s Vo ... rad/s + EAcceleration of Center of Mass of Rectangle 1 Ax Ax A Ay AUJAI Ae --- m/s^2 ... m/s^2 -- m/s^2 .-- rad/s^2 3.00 Aø Mass M1 = 2.25 kg is at the end of a rope that is 2.00 m in length. The initial angle with respect to the vertical is 60.0° and M1 is initially at rest. Mass M1 is released and strikes M2 = 4.50 kg exactly horizontally. The collision is elastic. After collision, mass M2 is moving on a frictionless surface, but runs into a rough patch 2.00…

I need help solving this problem.

Which datum has size? Please refer to image attached.

please put into DMS format with final solution. Thank you

nts) Simplify the following block diagram: S H Hint: redraw as: S R G H.

Can you write me a program manuscript using geometric definition on FAPT language. The starting point is P1 and starts where the blue dot is. P1 = 0,0