(a) Explanation The sign conventions for the stress components are explained below. The outward normal on the right-hand face of the element is representing as the positive x and x ' axes. The normal stress σ x and σ x ' are positive if it acts along the positive x and x ' axes. The normal stress σ y and σ y ' are positive if it acts along the positive y and y ' axes. The shear stress τ x y and τ x ' y ' are positive if it acts along the positive x and x ' and y and y ' axes. Calculation: Apply sign conventions to the given Figure. The value of normal stresses are σ x = − 12 ksi and σ y = − 8 ksi . The value of shear stress is τ x y = 4 ksi . The procedure to construct Mohr’s circle is shown below. The coordinate systems are the horizontal axis represents the normal stress with positive towards right and the vertical axis represents shear stress with positive downwards. Plot the center of the circle C which is located σ avg = σ x + σ y 2 from the origin. Plot the reference point A having coordinates A ( σ x , τ x y ) . This point represents that the x ′ axis coincides with the x axis. Hence, θ = 0 ° . Plot the reference point B having coordinates B ( σ y , − τ x y ) . Connect the point A with the centre C and find CA by trigonometry which represents the radius of the circle R . Sketch the circle. Find the average normal stress ( σ avg ) using the relation: σ avg = σ x + σ y 2 (1) Substitute − 12 ksi for σ x and − 8 ksi for σ y in Equation (1). σ avg = − 12 − 8 2 = − 10 ksi Therefore, the average normal stress is − 10 ksi _ . Therefore, the coordinates of the reference point C is ( − 10 , 0 ) . The coordinates of the reference point A ( σ x , τ x y ) = ( − 12 , 4 ) (b) To determine The maximum in-plane shear stress. The average normal stress. The orientation of the principal stresses. The orientation of the maximum in-plane shear stress.

9th Edition

ISBN: 9789810694364

Author: Russell C Hibbeler

Publisher: Pearson Education

See similar textbooks

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial…

Videos

Question

Chapter 9.4, Problem 9.59P

(a)

To determine

The principal stresses.

(b)

To determine

The maximum in-plane shear stress.

The average normal stress.

The orientation of the principal stresses.

The orientation of the maximum in-plane shear stress.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.4, Problem 9.58P

Chapter 9.4, Problem 9.60P

Students have asked these similar questions

Given answers to be: i) 14.65 kN; 6.16 kN; 8.46 kN ii) 8.63 kN; 9.88 kN iii) Bearing 6315 for B1 & B2, or Bearing 6215 for B1

(b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixed

Help ارجو مساعدتي في حل هذا السؤال

Chapter 9 Solutions

Mechanics Of Materials, Si Edition

Ch. 9.3 - In each case, the state of stress x, y, xy...Ch. 9.3 - Given the state of stress shown on the element,...Ch. 9.3 - Determine the normal stress and shear stress...Ch. 9.3 - Determine the equivalent state of stress on an...Ch. 9.3 - Also, find the corresponding orientation of the...Ch. 9.3 - Determine the equivalent state of stress on an...Ch. 9.3 - Determine the maximum principal stress at point B.Ch. 9.3 - Determine the principal stress at point C.Ch. 9.3 - Prove that the sum of the normal stresses x + y =...Ch. 9.3 - 9-2. The state of stress at a point in a member is...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.