String class: The “String” class provides a number of methods that examines for a string inside of a string. The term “substring” refers to a string that denotes another string’s part. The “startsWith” method would determine whether calling string of object begins with a particular substring. The method returns “true” if string begins with specified substring, it returns “false” otherwise. The “endsWith” method would determine whether calling string would end with a specified substring. The method returns “true” if string ends with specified substring, it returns “false” otherwise. The “regionMatches” method would determine whether specified regions for two strings match. The first argument of this method can be “true” or “false” that indicates whether a case-insensitive comparison could be performed. concat method: It returns a copy of calling string object with contents of given string concatenated to it. It performs same operation as “+” operator while used with strings. It returns a string with value of string passed into method, appended to end of string. It appends one string to another string’s end.

Question

Want to see the full answer?

Answer 1

Question

Chapter 9.3, Problem 9.12CP

Program Plan Intro

String class:

The “String” class provides a number of methods that examines for a string inside of a string.

The term “substring” refers to a string that denotes another string’s part.

The “startsWith” method would determine whether calling string of object begins with a particular substring.

The method returns “true” if string begins with specified substring, it returns “false” otherwise.

The “endsWith” method would determine whether calling string would end with a specified substring.

The method returns “true” if string ends with specified substring, it returns “false” otherwise.

The “regionMatches” method would determine whether specified regions for two strings match.

The first argument of this method can be “true” or “false” that indicates whether a case-insensitive comparison could be performed.

concat method:

It returns a copy of calling string object with contents of given string concatenated to it.

It performs same operation as “+” operator while used with strings.

It returns a string with value of string passed into method, appended to end of string.

It appends one string to another string’s end.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

15 points Save ARS Consider the following scenario in which host 10.0.0.1 is communicating with an external SMTP mail server at IP address 128.119.40.186. NAT translation table WAN side addr LAN side addr (c), 5051 (d), 3031 S: (e),5051 SMTP B D (f.(g) 10.0.0.4 server 138.76.29.7 128.119.40.186 (a) is the source IP address at A, and its value. S: (a),3031 D: (b), 25 10.0.0.1 A 10.0.0.2. 1. 138.76.29.7 10.0.0.3

6.3A-3. Multiple Access protocols (3). Consider the figure below, which shows the arrival of 6 messages for transmission at different multiple access wireless nodes at times t=0.1, 1.4, 1.8, 3.2, 3.3, 4.1. Each transmission requires exactly one time unit. 1 t=0.0 2 3 45 t=1.0 t-2.0 t-3.0 6 t=4.0 t-5.0 For the CSMA protocol (without collision detection), indicate which packets are successfully transmitted. You should assume that it takes .2 time units for a signal to propagate from one node to each of the other nodes. You can assume that if a packet experiences a collision or senses the channel busy, then that node will not attempt a retransmission of that packet until sometime after t=5. Hint: consider propagation times carefully here. (Note: You can find more examples of problems similar to this here B.] ☐ U ப 5 - 3 1 4 6 2

Just wanted to know, if you had a scene graph, how do you get multiple components from a specific scene node within a scene graph? Like if I wanted to get a component from wheel from the scene graph, does that require traversing still? Like if a physics component requires a transform component and these two component are part of the same scene node. How does the physics component knows how to get the scene object's transform it is attached to, this being in a scene graph?