Explanation The Figure-(1) shown below represents the temperature-entropy diagram for both the cycles. Figure-(1) The main purpose of the regenerator is to produce the heat in the working fluid (air) just before it enters the combustion chambers seeking help from the turbine exit. For this, the temperature of the air leaving the turbines must be at a higher temperature than the air entering the turbine. In the cycle 1-2-3-4, air leaving the turbine at state-4 is at a higher temperature than the air entering the combustion chamber at state-2. Thus, the cycle permits the use of regenerator...

Appendices to accompany Fundamentals of Engineering Thermodynamics, 8e

8th Edition

ISBN: 9781118957219

Author: Michael J. Moran, Howard N. Shapiro

Publisher: WILEY

See similar textbooks

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. T…

Videos

Question

Chapter 9.14, Problem 8CU

To determine

The cycle that does not allow the use of regenerator.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.14, Problem 7CU

Chapter 9.14, Problem 9CU

Students have asked these similar questions

Water at 20 o C enters the 4 cm-diameter, 14 m-long tube at a rate of 0.8 kg/s. The surfacetemperature of the pipe is maintained at 165 o Cby condensing geothermal stream at the shellside of the heat exchanger. Use water properCesat 85 o C for all calculaCons.(a) Show that the water flow is turbulent and thermally fully developed. (b) EsCmate the heat transfer coefficient for convecCve heat transfer from the pipe to the water. For a fully developed turbulent flow within the smooth pipe, the Nu number can becalculated from the following equaCon:(c) Calculate the exit temperature of the water. (d) Share your opinion on whether the use of water properties at 85°C is appropriate. Yes or No because:

Consider a hot automotive engine, which can beapproximated as a 0.5-m-high, 0.40-m-wide, and 0.8-m-long rectangular block. The bottom surface of the block isat a temperature of 100°C and has an emissivity of 0.95.The ambient air is at 20°C, and the road surface is at25°C. Determine the rate of heat transfer from the bottomsurface of the engine block by convection and radiationas the car travels at a velocity of 80 km/h. Assume theflow to be turbulent over the entire surface because of theconstant agitation of the engine block. a) Calculate convective heat transfer coefficient (h). b) Calculate the total heat transfer rate

8 mm- Top view -200 mm-180 mm- D B B 12 mm Side view B -8 mm D PROBLEM 1.56 In an alternative design for the structure of Prob. 1.55, a pin of 10-mm-diameter is to be used at A. Assuming that all other specifications remain unchanged, determine the allowable load P if an overall factor of safety of 3.0 is desired. PROBLEM 1.55 In the structure shown, an 8- mm-diameter pin is used at A, and 12-mm- diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired. 20 mm P 8 mm- 12 mm- Front view

Chapter 9 Solutions

Appendices to accompany Fundamentals of Engineering Thermodynamics, 8e

Ch. 9.14 - Prob. 1E Ch. 9.14 - Prob. 2E Ch. 9.14 - Prob. 3E Ch. 9.14 - Prob. 4E Ch. 9.14 - Prob. 5E Ch. 9.14 - 6. What is the purpose of a rear diffuser on a...Ch. 9.14 - 7. What is the meaning of the octane rating that...Ch. 9.14 - Prob. 8E Ch. 9.14 - Prob. 9E Ch. 9.14 - 10. What is the purpose of the gas turbine–powered...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.