Concept explainers
Predict/Calculate Weighing a Block on an Incline A wedge of mass m, is firmly attached to the top of a scale as shown in Figure 9-47. The inclined surface of the wedge makes an angle θ with the horizontal Now a block of mass m2 is placed on the inclined surface of the wedge and allowed to accelerate without friction down the slope (a) Show that the reading on the scale while the block slides is
(m1 + i2 cos2θ)g
(b) Explain why the reading on the scale is less than (m1 + m1)g. (c) Show that the expression in part (a) gives the expected results for θ = 0 and θ = 90°.
Figure 9-47
Problem 87
Want to see the full answer?
Check out a sample textbook solutionChapter 9 Solutions
EBK PHYSICS
Additional Science Textbook Solutions
Biology: Life on Earth (11th Edition)
Organic Chemistry (8th Edition)
Human Anatomy & Physiology (2nd Edition)
Applications and Investigations in Earth Science (9th Edition)
Human Physiology: An Integrated Approach (8th Edition)
Biology: Life on Earth with Physiology (11th Edition)
- We know from studying friction forces that static friction increases with increasing normal force between the surfaces, which becomes important for vehicles traveling on icy or snowy roads that have coefficients of static friction much smaller than those of dry pavement. In particular, the greater the normal force on the drive wheels (those coupled to the engine), the better the traction. The horizontal position of the center of mass of a typical compact automobile is located 1.1 m toward the rear as measured from the front wheel axle. The wheelbase (distance from the front wheel axle to the rear wheel axle) is 2.7 m. Assume the car is stationary on level ground and has a weight of 12,000 N. Determine the total normal force on the two front tires and on the two rear tires. Which do you suppose are the drive wheels in this case?arrow_forwardVery large forces are produced in joints when a person jumps from some height to the ground. (a) Calculate the magnitude of the force produced if an 80.0-kg person jumps from a 0.600-m-high ledge and lands stiffly, compressing joint material 1.50 cm as a result. (Be certain to include the weight of the person.) (b) In practice the knees bend almost involuntarily to help extend the distance over which you stop. Calculate the magnitude of the force produced if the stopping distance is 0.300 m. (c) Compare both forces with the weight of the person.arrow_forwardA 0.500-kg potato is fired at an angle of 80.0 above the horizontal from a PVC pipe used as a “potato gun” and reaches a height of 110.0 m. (a) Neglecting air resistance, calculate the potato’s velocity when it leaves the gun. (b) The gun itself is a tube 0.430 m long. Calculate the average acceleration of the potato in the tube as it goes from zero to the velocity found in (a). (c) What is the average force on the potato in the gun? Express your answer in newtons and as a ratio to the weight of the potato.arrow_forward
- To get in shape, you head to the local gym to exercise by lifting weights. Using a lat machine (Fig. P5.48), you notice that the wire connected to the bar is run around three different pulleys and is connected to a vertical stack of weights on the other end. The weights move up and down as you pull down on the bar. Suppose you set the machine so that the weight to be lifted is 120.0 lb. When you pull down on the bar, exerting a constant force, the acceleration experienced by the weights is 0.250 m/s2. What tension must exist in the wire connecting the bar and weights under these conditions? Assume the pulleys are massless and frictionless. FIGURE P5.48arrow_forwardA uniform pole is propped between the floor and the ceiling of a room. The height of the room is 7.80 ft, and the coefficient of static friction between the pole and the ceiling is 0.576. The coefficient of static friction between the pole and the floor is greater than that between the pole and the ceiling. What is the length of the longest pole that can be propped between the floor and the ceiling?arrow_forwardI don't understand the question belowarrow_forward
- 5-82. The sign has a mass of 100 kg with center of mass at G. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in wires BC and BD. QD 1'm 2 m •G 1 m 1 marrow_forward*15-132. Sand is deposited from a chute onto a conveyor belt which is moving at 0.5 m/s. If the sand is assumed to fall vertically onto the belt at A at the rate of 4 kg/s, determine the belt tension Fg to the right of A.The belt is free to move over the conveyor rollers and its tension to the left of A is Fc= 400 N. 0.5 m/s Fc = 400 Narrow_forwardMENG230 *8-44. The 3-Mg rear-wheel-drive skid loader has a center of mass at G. Determine the largest number of crates that can be pushed by the loader if each crate has a mass of 500 kg. The coefficient of static friction between a crate and the ground is u,= 0.3, and the coefficient of static friction between the rear wheels of the loader and the ground is u = 0.5. The front wheels are free to roll. Assume that the engine of the loader is powerful enough to generate a torque that will cause the rear wheels to slip. 92 Class comm Asd a class comaarrow_forward
- What's this?arrow_forwardTwo identical balls of mass “m” are released from rest from a height “h” on two ramps of different inclinations as shown in the figure. Which of the following is true for this scenario? Assume all surfaces to be smooth. a) Both A and B reach the bottom at the same time b) A reaches the bottom before B c) A reaches the bottom before B d) Depends on the angles a and a’arrow_forwardAt an accident scene on a level road, investigators determine that a car slid for a distance 72 m before coming to a stop. It was a rainy day and the coefficient of friction was estimated to be 0.36. - What was the speed of the car when the driver slammed on the brakes? - Why does the car's mass not matter?arrow_forward
- College PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Classical Dynamics of Particles and SystemsPhysicsISBN:9780534408961Author:Stephen T. Thornton, Jerry B. MarionPublisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning