To what is the turning force of a d’Arsonval meter movement proportional?
The quantity to which the turning force of a d’Arsonval meter movement proportional to?
Answer to Problem 1RQ
The turning force of a d’Arsonval meter movement is proportional to the strength of the magnetic field developed in the current carrying coil.
Explanation of Solution
Description:
The underlying principle behind operation of the d’Arsonval meter movementis that like magnetic poles repel each other. The turning force of depends on the repulsion of magnetic fields. A magnetic field is created around the coilas current passes through it.
The flow of current is such that the polarity of the permanent magnet and that of the magnetic pole created around the coil is the same. As like magnetic poles repel each other, the coil is deflected away from the pole of the magnet. A spring provides the damping movement to the turning of the coil. The turning distance against the spring is proportional to the strength of the magnetic field developed in the current carrying coil.
Conclusion:
The quantity on which the turning force of a d’Arsonval meter movement is dependant has been explained.
Want to see more full solutions like this?
Chapter 9 Solutions
Delmar's Standard Textbook Of Electricity
- multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -arrow_forwardBook:Grifith electrodynamicsarrow_forwardWhat is the voltage across the plates of capacitor #1 (C1)? Select one: a. 6.36 volts b. 2.71 volts c. 5.65 volts d. 7.32 voltsarrow_forward
- Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V laarrow_forwardThe waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =arrow_forwardwhat is relationship between peak voltage and firing angle (alpha) in thyristor, explanarrow_forward
- With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hzarrow_forwardQuestion 777 electric plot the output voltage when the resister and capacitor in the series branch and the resister and capacitor in parallel branch are unequal and have fluctuations of of +-15% of the nominal values and analyze the signals Full explain this question and text typing work only thanksarrow_forwardhi there, I am looking for a solutiopn to part (b) of this please. Thanks in advance I really appreciate itarrow_forward
- An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin. Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohmsarrow_forwardThe waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 30 V/cm. Determine the (1) amplitude of waveform Q, (i) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =arrow_forwardConsider the following statements :A clamper circuit 1. adds or subtracts a dc voltage to a waveform 2. does not change the waveform 3. amplifies the waveform Which are correct? * O 1,2 O 1,3 O 1, 2, 3 O 2,3arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,