EBK NUMERICAL METHODS FOR ENGINEERS
EBK NUMERICAL METHODS FOR ENGINEERS
7th Edition
ISBN: 8220100254147
Author: Chapra
Publisher: MCG
bartleby

Videos

Textbook Question
Book Icon
Chapter 9, Problem 1P

(a) Write the following set of equations in matrix form:

8 = 6 x 3 + 2 x 2 2 x 1 = x 3 5 x 2 + 8 x 1 = 13

(b) Multiply the matrix of coefficients by its transpose; i.e., [ A ] [ A ] T .

(a)

Expert Solution
Check Mark
To determine

The matrix form of the following set of equations,

8=6x3+2x22x1=x35x2+8x1=13

Answer to Problem 1P

Solution:

The matrix form of the set of equations is, [026101850]{x1x2x3}={8213}.

Explanation of Solution

Given:

The set of equations,

8=6x3+2x22x1=x35x2+8x1=13

Consider the set of equations,

8=6x3+2x22x1=x35x2+8x1=13

The set of equations can be written as,

0x1+2x2+6x3=8x1+0x2+x3=28x1+5x2+0x3=13

These equations have three unknowns x1, x2 and x3.

The matrix form of the above set of equations can be written as,

[A]{X}={B}

Where, A is the coefficient matrix.

Therefore, the matrix form of the set of equations is,

[026101850]{x1x2x3}={8213}.

(b)

Expert Solution
Check Mark
To determine

To calculate: The matrix multiplication of the coefficient matrix with its transpose, that is [A].[A]T. Where the coefficient matrix is, [A]=[026101850].

Answer to Problem 1P

Solution:

The matrix multiplication of the coefficient matrix with its transpose is,

[A].[A]T=[4061062810889]

Explanation of Solution

Given:

The coefficient matrix, [A]=[026101850].

Formula used:

Transpose of the matrix A is denoted by AT. If A is any matrix [abcdefghi], then its transpose will be [adgbehcfi].

Calculation:

Consider the coefficient matrix,

[A]=[026101850]

The transpose of the matrix A is denoted by [A]T and is equal to,

[A]T=[018205610]

Multiplication of the coefficient matrix and its transpose is,

[A].[A]T=[026101850].[018205610]=[0×0+2×2+6×60×1+2×0+6×10×8+2×5+6×01×0+0×2+1×61×1+0×0+1×11×8+0×5+1×08×0+5×2+0×68×1+5×0+0×18×8+5×5+0×0]=[4+3661062810864+25]=[4061062810889]

Therefore, the matrix multiplication of the coefficient matrix with its transpose is,

[A].[A]T=[4061062810889].

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Assignment 10, Question 4, Problem Book #202 Problem Statement An ideal Brayton cycle with a two-stage compressor, a two-stage turbine, and a regenerator operates with a mass flow rate of 25 kg/s. The regenerator cold inlet is at 490 K and its effectiveness is 60%. Ambient conditions are 90 kPa and 20°C. The intercooler operates at 450 kPa and the reheater operates at 550 kPa. The temperature at the exit of the combustion chamber is 1,400 K. Heat is removed in the intercooler at a rate of 2.5 MW and heat is added in the reheater at a rate of 10 MW. Determine the thermal efficiency and the back work ratio. Use a cold air standard analysis with cp = 1.005 kJ/(kg K) and k = 1.4. . Answer Table Stage Description Your Answer Correct Answer Due Date Grade (%) 1 Thermal efficiency (%) Dec 5, 2024 11:59 pm 0.0 1 Weight Attempt Action/Message 1/5 Part Type Submit 1 Back work ratio (%) Dec 5, 2024 11:59 pm 0.0 1 * Correct answers will only show after due date has passed.
Assignment 10, Question 3, Problem Book #198 Problem Statement Consider a Brayton cycle with a regenerator. The regenerator has an effectiveness of 75%. The compressor inlet conditions are 1.2 bar and 300 K and the mass flowrate is 4.5 kg/s. The compressor outlet pressure is 9 bar. Both the compressor and turbine consist of a single isentropic stage. What minimum power output must be achieved before the regenerator begins to have a benefit? Use an air-standard analysis. Answer Table Correct Answer Stage Description Your Answer Due Date Grade (%) Part Weight Attempt Action/Message Туре 1 Power output (MW) Dec 5, 2024 11:59 pm 0.0 1 1/5 Submit * Correct answers will only show after due date has passed.
Q-3 Consider an engine operating on the ideal Diesel cycle with air as the working fluid. The volume of the cylinder is 1200 cm³ at the beginning of the Compression process, 75 cm³ at the end, and 150 cm³ after the heat addition process. Air is at 17°c and lookpa at the beginning of the compression proc ess. Determine @ The pressure at the beginning of the heat rejection process. the net work per cycle in kjⒸthe mean effective pressur. Answers @264.3 KN/m² ②0.784 kj or 544-6 kj © 697 KN 19 2 m
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Matrix Factorization - Numberphile; Author: Numberphile;https://www.youtube.com/watch?v=wTUSz-HSaBg;License: Standard YouTube License, CC-BY