DESCRIBE THE PROCESSES AND CYCLES?

Q: Compression ratio in Diesel Cycle will be 2.5 time higher than the cutoff ratio. Volume at TDC is…

A: For solution refer below images.

Q: An air-standard Otto cycle is often used as a very simplified model of a spark- ignition engine. The…

A: P-V diag

Q: A square tank of water (18 inx18 in) is drained from 15 inches to 14 inches with an orifice size of…

A:

Q: The example for forming process is ___________. a. Tempering b. Drawing c. Gas welding d. Die…

A: The example of forming process is drawing in which material goes under plastic deformation.

Q: how to calculate work done for each process?

A: Given: Process 1 to 2 is a reversible isothermal expansion process from pressure P1 to P2 at…

Q: Complete this table for refrigerant-134a: T, P, kPa h, kJ/kg PI °C desc -4 320 10 100 050 Satuu

A: Given Data : R-134a Refrigerant

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: Define the Temperature Scales?

A:

Q: Q3: You have a truss which is shown below, two forces applying on it in B and C joints, which are…

A:

Q: µA ? The cooling unit has a total weight of 50 kip and a center of gravity at G. (Figure 1) Value…

A:

Q: High c/a-ratio metals such as Zn will have the following property? (b) having high r-value (d) all…

A: Solution: Zn having Hexagonal closed packing structure has c/a ratio of the order of 1.856 with…

Q: 5. Determine the Miller indices for the following structural elements (SHOW YOUR WORK). Do PLANES A…

A: To determine:Miller indices of Plane A and Plane B.

Q: Part Three: In the diagram at the right, ABC represents a post-beam system rotating about an axis…

A:

Q: 23) The example for forming process is ___________. a. Extrusion b. Tempering c. Die Casting d. Gas…

A: Forming is a manufacturing process by which metal parts are converted into products through…

Q: 3-The flywheel of an internal combustion engine maintains the smooth rotary motion of the O (A)…

A: 1. The flywheel of an internal combustion engine maintains the smooth rotatory motion of the....…

Q: the wind vane indicating the direction of the wind relative to the ship. After th ship changes…

A:

Q: Prob 2. Find the mass of air in a closed chamber measuring 35 ft x 20 ft x 10 ft, when the pressure…

A: Given data- dimension of the closed chamber = 35 ft * 20 ft * 10 ft Pressure (P) = 17 lb/in2…

Q: Explain revision B?

A: As you can see in below image, at highlighted location, in revision B, there is diameter with upper…

Q: Take the micro-body from the self-loading member, and bear the stress on it as shown in Figure a.…

A: For the given stress element,…

Q: Determine the angular acceleration AB (positive if counterclockwise, negative if clockwise) of link…

A: The angular velocity of OB is θ˙=0 The angular acceleration of OB is θ¨=3.3 rad/s2 The angle is…

Q: A cantilever beam of length 700 mm, width 55 mm and thickness 15 mm is made of steel with Young's…

A:

Q: PROBLEM 1.3 3 in. 2 in. 30 kips B Two solid cylindrical rods AB and BC are welded together at B and…

A:

Q: Solving Equation 5 for a in terms of the measured quantities x and t gives 2x (Eq. 6) a = t2

A: As given in table for mass difference (m2-m1) Kg the acceleration and applied force can be…

Q: The control rod AC is guided by two pins that slide freely in parallel curved slots of radius 199…

A:

Q: II Review • Part C In your summer job with a venture capital firm, you are given funding requests…

A:

Q: Two gaseous streams enter a mixing chamber through two sections and leaves through one section.…

A:

Q: Where did the 196.2 in equation 2 come from?

A:

Q: Problem 2: Four Processes are shown below. Each process occurs in a well-insulated piston cylinder…

A: Here I am going to arrange the temperature in highest to lowest order.

Q: . An involute gear of 16 teeth drives another 26 teeth gear. The diametral pitch is 3 and the…

A:

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.