Explanation Given information : The height of the ladder, l = 15 ft . The weight of the ladder, W = 80 lb . The coefficient of static friction at point A , μ = 0.4 . The coefficient of static friction at point B , μ = 0.4 . Show the free body diagram of the ladder resting against the wall as in Figure (1). Conclusion: As the ladder is required to be on the verge to slide down, calculate the friction force acting at A and B . Calculate the frictional force at A . F A = μ N A (I) Here, the normal force at A is N A . Substitute 0.4 for μ in Equation (I). F A = 0.4 N A Calculate the frictional force at B . F B = μ N B (II) Here, the normal force at B is N B . Substitute 0.4 for μ in Equation (II). F B = 0.4 N B Refer Figure (1) and resolve the forces in the horizontal direction. + → ∑ F x = 0 F A − N B = 0 (III) Substitute 0.4 N A for F A in Equation (III). 0.4 N A − N B = 0 N B = 0.4 N A Refer Figure (1) and resolve the forces in the vertical direction. + ↑ ∑ F x = 0 N A + F B − W = 0 (IV) Substitute 0.4 N B for F B and 80 lb for W in Equation (IV). N A + 0.4 N B − 80 = 0 (V) Substitute 0.4 N A for N B in Equation (V). N A + 0

13th Edition

ISBN: 9780132915540

Author: Russell C. Hibbeler

Publisher: Prentice Hall

See similar textbooks

Question

Chapter 8.2, Problem 6P

To determine

The smallest angle θ at which the ladder will not slip.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 8.2, Problem 5P

Chapter 8.2, Problem 7P

Students have asked these similar questions

I need help answering parts a and b

Required information Water initially at 200 kPa and 300°C is contained in a piston-cylinder device fitted with stops. The water is allowed to cool at constant pressure until it exists as a saturated vapor and the piston rests on the stops. Then the water continues to cool until the pressure is 100 kPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Water 200 kPa 300°C On the T-V diagram, sketch, with respect to the saturation lines, the process curves passing through the initial, intermediate, and final states of the water. Label the T, P, and V values for end states on the process curves. Please upload your response/solution by using the controls provided below.

A piston-cylinder device contains 0.87 kg of refrigerant-134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Use data from the tables. R-134a -10°C Determine the change in the volume of the cylinder of the refrigerant-134a if the specific volume and enthalpy of R-134a at the initial state of 90.4 kPa and -10°C and at the final state of 90.4 kPa and 15°C are as follows: = 0.2418 m³/kg, h₁ = 247.77 kJ/kg 3 v2 = 0.2670 m³/kg, and h₂ = 268.18 kJ/kg The change in the volume of the cylinder is m

Chapter 8 Solutions

Engineering Mechanics: Statics

Ch. 8.2 - Determine the friction developed between the 50-kg...Ch. 8.2 - Determine the minimum force P to prevent the 30-kg...Ch. 8.2 - Determine the maximum force P that can be applied...Ch. 8.2 - If the coefficient of static friction at contact...Ch. 8.2 - Determine the maximum force P that can be applied...Ch. 8.2 - Prob. 6FP Ch. 8.2 - Blocks A, B, and C have weights of 50 N, 25 N, and...Ch. 8.2 - If the coefficient of static friction at all...Ch. 8.2 - Using the coefficients of static friction...Ch. 8.2 - Prob. 1P

Ch. 8.2 - The tractor exerts a towing force T=400 lb....Ch. 8.2 - The winch on the truck is used to hoist the...Ch. 8.2 - Prob. 4P Ch. 8.2 - Prob. 5P Ch. 8.2 - Prob. 6P Ch. 8.2 - The block brake consists of a pin-connected lever...Ch. 8.2 - The block brake consists of a pin-connected lever...Ch. 8.2 - Prob. 9P Ch. 8.2 - Prob. 10P Ch. 8.2 - The block brake is used to stop the wheel from...Ch. 8.2 - If a torque of M=300 Nm is applied to the...Ch. 8.2 - The cam is subjected to a couple moment of 5N m....Ch. 8.2 - Determine the maximum weight W the man can lift...Ch. 8.2 - The car has a mass of 1.6 Mg and center of mass at...Ch. 8.2 - Prob. 16P Ch. 8.2 - Prob. 17P Ch. 8.2 - Prob. 18P Ch. 8.2 - Prob. 19P Ch. 8.2 - Prob. 20P Ch. 8.2 - Prob. 21P Ch. 8.2 - Prob. 22P Ch. 8.2 - A 35-kg disk rests on an inclined surface for...Ch. 8.2 - The man has a weight of 200 lb, and the...Ch. 8.2 - Prob. 25P Ch. 8.2 - Prob. 26P Ch. 8.2 - Prob. 27P Ch. 8.2 - Prob. 28P Ch. 8.2 - Prob. 29P Ch. 8.2 - Prob. 30P Ch. 8.2 - If the coefficient of static friction at A and B...Ch. 8.2 - Prob. 32P Ch. 8.2 - Prob. 33P Ch. 8.2 - Prob. 34P Ch. 8.2 - Prob. 35P Ch. 8.2 - Prob. 36P Ch. 8.2 - Prob. 37P Ch. 8.2 - Prob. 38P Ch. 8.2 - Prob. 39P Ch. 8.2 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8.2 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8.2 - Prob. 42P Ch. 8.2 - Prob. 43P Ch. 8.2 - Prob. 44P Ch. 8.2 - Prob. 45P Ch. 8.2 - The beam AB has a negligible mass and thickness...Ch. 8.2 - It is supported at one end by a pin and at the...Ch. 8.2 - Prob. 48P Ch. 8.2 - Prob. 49P Ch. 8.2 - Prob. 50P Ch. 8.2 - Prob. 51P Ch. 8.2 - Prob. 52P Ch. 8.2 - The wheel weights 20 lb and rests on a surface for...Ch. 8.2 - Prob. 54P Ch. 8.2 - Determine the greatest angle so that the ladder...Ch. 8.2 - Prob. 56P Ch. 8.2 - Prob. 57P Ch. 8.2 - Prob. 4CP Ch. 8.4 - Determine the largest angle that will cause the...Ch. 8.4 - If the beam AD is loaded as shown, determine the...Ch. 8.4 - Prob. 60P Ch. 8.4 - Prob. 61P Ch. 8.4 - If P=250 N, determine the required minimum...Ch. 8.4 - Determine the minimum applied force P required to...Ch. 8.4 - Prob. 64P Ch. 8.4 - Prob. 65P Ch. 8.4 - Prob. 66P Ch. 8.4 - Prob. 67P Ch. 8.4 - If the clamping force on the boards is 600 lb,...Ch. 8.4 - Prob. 69P Ch. 8.4 - If the force F is removed from the handle of the...Ch. 8.4 - If the clamping force at G is 900 N, determine the...Ch. 8.4 - If a horizontal force of F = 50 N is applied...Ch. 8.4 - Prob. 73P Ch. 8.4 - Prob. 74P Ch. 8.4 - The shaft has a square-threaded screw with a lead...Ch. 8.4 - Prob. 76P Ch. 8.4 - Prob. 77P Ch. 8.4 - Prob. 78P Ch. 8.4 - If a horizontal force of P = 100 N is applied...Ch. 8.4 - Determine the horizontal force P that must be...Ch. 8.4 - Prob. 81P Ch. 8.4 - Prob. 82P Ch. 8.5 - A cylinder having a mass of 250 kg is to be...Ch. 8.5 - A cylinder having a mass of 250 kg is to be...Ch. 8.5 - Prob. 85P Ch. 8.5 - Prob. 86P Ch. 8.5 - Prob. 87P Ch. 8.5 - The coefficient of static friction between the...Ch. 8.5 - Prob. 89P Ch. 8.5 - Prob. 90P Ch. 8.5 - Prob. 91P Ch. 8.5 - Prob. 92P Ch. 8.5 - Prob. 93P Ch. 8.5 - Determine the weight of the cylinder if the...Ch. 8.5 - If slipping does not occur at the wall, determine...Ch. 8.5 - Prob. 96P Ch. 8.5 - Prob. 97P Ch. 8.5 - Show that the frictional relationship between the...Ch. 8.5 - Prob. 99P Ch. 8.5 - Determine the largest angles so that the cord...Ch. 8.5 - Prob. 101P Ch. 8.5 - Determine the smallest counterclockwise twist or...Ch. 8.5 - Prob. 103P Ch. 8.5 - Prob. 104P Ch. 8.5 - Determine the smallest stretch of the spring...Ch. 8.5 - Idler pulley A, and motor pulley B. If the motor...Ch. 8.8 - Prob. 107P Ch. 8.8 - Prob. 108P Ch. 8.8 - Prob. 109P Ch. 8.8 - Prob. 110P Ch. 8.8 - Prob. 111P Ch. 8.8 - Prob. 112P Ch. 8.8 - Prob. 113P Ch. 8.8 - Prob. 114P Ch. 8.8 - Prob. 116P Ch. 8.8 - Prob. 117P Ch. 8.8 - Prob. 118P Ch. 8.8 - Prob. 119P Ch. 8.8 - Prob. 120P Ch. 8.8 - Prob. 121P Ch. 8.8 - Prob. 122P Ch. 8.8 - Prob. 123P Ch. 8.8 - Prob. 124P Ch. 8.8 - Prob. 125P Ch. 8.8 - Prob. 126P Ch. 8.8 - Prob. 127P Ch. 8.8 - The vehicle has a weight of 2600 lb and center of...Ch. 8.8 - The tractor has a weight of 16 000 lb and the...Ch. 8.8 - Prob. 130P Ch. 8.8 - Prob. 131P Ch. 8.8 - Prob. 132P Ch. 8.8 - Prob. 133RP Ch. 8.8 - Prob. 134RP Ch. 8.8 - Prob. 135RP Ch. 8.8 - Prob. 136RP Ch. 8.8 - The three stone blocks have weights of, WA =...Ch. 8.8 - The uniform 60-kg crate C rests uniformly on a...Ch. 8.8 - Prob. 139RP Ch. 8.8 - Prob. 140RP Ch. 8.8 - Prob. 141RP Ch. 8.8 - Prob. 142RP Ch. 8.8 - Prob. 143RP Ch. 8.8 - Prob. 144RP

Knowledge Booster