Principles of Foundation Engineering (MindTap Course List)
Principles of Foundation Engineering (MindTap Course List)
8th Edition
ISBN: 9781305081550
Author: Braja M. Das
Publisher: Cengage Learning
bartleby

Concept explainers

Question
Book Icon
Chapter 8, Problem 8.6P
To determine

Calculate the consolidation settlement under the center of mat foundation.

 </TO-DETERMINE>

The consolidation settlement under the center of mat foundation is 125mm¯.

Given information:

The length of the foundation is L=12m.

The width of the foundation is B=10m.

The depth of the foundation Df is 2.2m

The load value Q is 30MN.

The preconsolidation pressure σc is 105kN/m2.

The depth values are x1=2m, x2=2m and x3=5.2m

Calculation:

Find the consolidation settlement at the center of the foundation using the relation.

Sc(p)=CcHc1+eologσo+Δσavσo

Find the stress σo

σo=4.2m×16kN/m3+2m×189.81+5.2m2×17.59.81=67.2+16.38+19.99=103.57kN/m2

Height of clay Hc=5.2m

Cc=0.38eo=0.88

Find the net load per unit area using the relation.

q=QAγDf=30MN×1000kN1MN10×1216×2.2=214.8kN/m2

Find the average stress increase in the clay layer below the corner of each rectangular area.

ΔσavH2/H1=qoH2Ia(H2)H1Ia(H1)H2H1=214.82+2+5.2Ia(H2)2+2Ia(H1)5.2

For Ia(H2),

m2=BH2=52+2+5.2=0.543

n2=LH2=62+2+5.2=0.652

Refer to Figure 6.11, “Influence factor Ia” in the textbook.

Take the influence factor Ia(H2) as 0.186 for the value of m2=0.543 and n2=0.652.

For Ia(H1),

m2=BH1=52+2=1.25

n2=LH2=62+2=1.5

Refer to Figure 6.11, “Influence factor Ia” in the textbook.

Take the influence factor Ia(H1) as 0.23 for the value of m2=1.25 and n2=1.5.

ΔσavH2/H1=qoH2Ia(H2)H1Ia(H1)H2H1=214.82+2+5.20.1862+20.235.2=32.68kN/m2

Find the consolidation settlement at the center of the foundation using the relation.

Sc(p)=CcHc1+eologσo+Δσavσ=0.38×5.21+0.88log103.57+32.68103.57=0.125m=125mm

Therefore, the consolidation settlement under the center of mat foundation is 125mm¯.

Blurred answer
Students have asked these similar questions
Factor of Safety Activity The lap joint is connected by three 20-mm diameter rivets. Assuming that the applied allowable load, P=50kN is distributed equally among the three rivets and a factor of safety of 1.5, find: (a) the failure shear stress in a rivet, and (b) failure bearing stress between the plate and rivet 25 mm 25 mm
Draw the shear and moment diagrams of the beam CDE showing all calculations.  Assume the support at A is a roller and B is a pin.  There are fixed connected joints at D and E.  Assume P equals 9.6 and w equals 0.36
Find the length of the diagonal on the x-z plane (square root of square of sides). Find angle between the vector F and its projection on x-z (the diagonal defined above). Find Horizontal Projection of F on x-z plane, Fh, and vertical component, FY. Find projections of Fh, to define in-plane components Fx and Fz. Show that results match those of Problem 2(a) above. (2,0,4) F₂ 100 N (5, 1, 1)
Knowledge Booster
Background pattern image
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Text book image
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning
Text book image
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning
Text book image
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning