60° -B -6.5 kN A - 2.5 m - 80 80 25 mm |C 160 mm 25 mm

Q: Z 0.3m 4.25 kN 5 KN 0.4m 100 KN 100 KN 3.0 kN m 0.1m 2 kN 2,00 KN 200 KN La X This stainless steel…

A:

Q: A flexible connection consisting of rubber pads(thickness t =9 mm) bonded to steel plates is shown…

A: Given   Force P =16 kN Shear modulus for the rubber is G = 1250 kPa Thickness t =9 mm Find…

Q: Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume…

A:

Q: 10 kN 3 kN/m 100 mm 200 mm B 1.5 m 1.5 m 2.2 m

A:

Q: the beam shown in Figure (2), determine transverse shear stresses E, F and G on the cross section.…

A: Given P=100kNINA=470016mm4

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: 80 kN 80 kN 90 cm 90 cm N.A. 80 kN 80 kN (a)

A: Since it can be seen from the figure that the loading is symmetrical about the mid-point of the…

Q: 500lb 3ft B 2500lb 3ft 3ft N.A y=0 6ft 6 in lin X 3000lb ↓ lin 4in lin lin 9ft

A:

Q: Cable DB supports canopy beam OABCas shown in the figure. Find the required cross-sectionalarea of…

A: Draw a diagram for the problem. Here, T is the tension in the cable, θ is the angle made by the…

Q: The beam shown in the figure is made of Wood that has an Allowable Shear Stress of 200 psi;…

A:

Q: A cantilevered beam of rectangular section (b width=3 inches ), h camber=12 inches ) is subjected to…

A: A cantilevered beam of rectangular section width b= 3 in h=12 in load P=17 lb  c=2.5 ft from the…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

A:

Q: A simply supported I beam is 12 metres long with a midspan point load of 15 kN and a uniformly…

A:

Q: Consider the beam shown in sketch below, hinge supported at point A and roller supported at point D.…

A: Considering the cross-section of the beam The web is denoted as 1 and flange is denoted as 2

Q: At an arbitrary cross-section, a - a the state of stress is obtained at various points (point 1 ~ 5,…

A:

Q: 120 KN 100 mm H 400 mm B 22m 150 mm Find the shear stress at point H on the beam. The wall thickness…

A:

Q: Find the transverse shear stress in the material 3 in. from the top surface of the beam shown in the…

A: The shear force of cross section is .The transverse shear stress is defined as the shear stress that…

Q: The internal shear force at a certain section of a steel beam is V = 185 kN. The beam cross section…

A: To findthe shear stress at point A, which is located at  below the centroid of the wide-flange…

Q: 14. A prismatic bar having cross-sectional area A=1200 mm² is compressed by an axial load P = 90kN…

A: Step 1: Explanation for question

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.