500lb 3ft B 2500lb 3ft 3ft N.A y=0 6ft 6 in lin X 3000lb ↓ lin 4in lin lin 9ft

Q: For the Simply Supported Beam Carrying Four point loads, as shown in the Figure,     (a) Determine…

A:

Q: 2- Determine the minimum width b of the beam shown in the figure belov the flexural stress is not to…

A: The free body diagram is,

Q: Q3: Draw the shear force and bending moment diagrams for the loaded beam shown (see figure below). (…

A: Draw the free-body diagram of the beam.

Q: a) Find the maximum normal stress and maximum shear stress. b) Compare these values with the…

A: We are to determine the shear stress  and normal bending stress for the beam For this we will…

Q: (6) For the composite beam shown in the figure, which is bended about a horizontal axis by a couple…

A:

Q: Q - (A) // The figure A shown that the beam which is supported with a pin at A and a roller at B,…

A:

Q: 80 kN 80 kN 90 cm 90 cm N.A. 80 kN 80 kN (a)

A: Since it can be seen from the figure that the loading is symmetrical about the mid-point of the…

Q: For the beam with the cross-section shown, given that: V= 100 N b= 20 cm h=20 cm The max shear…

A:

Q: Since the bending safety stress em = 10 MPa, shear safety stress em = 600 kPa of the rectangular…

A:

Q: 2) mid section t=4mm 3 45 ** 5cm 5um 5c

A: Data given: The force acting at the free end, P = 100 N The length of the cantilever beam, L= 1 m…

Q: 4.5-18 Beam ABCwith an overhang at one end supports a partial uniform load of intensity 12 kN/m and…

A:

Q: The beam is supported by a pin at B and a roller at D. The applied loads shown in the figure have…

A: here, F1=790 lbF2=610 lbw= 140 lb/fta=6 ftb=13.8 ftc= 4.8 ft

Q: H.W: Find the values of the shear stress at point A, 3, and C in the beam Cross- Sedion shown in the…

A: A circular hollow cross-section shaft is subjected to a shear force of 100 kN. Points A, B, and C is…

Q: A floor system in a small building consistsof wood planks supported by 2-in. (nominal width)joists…

A: Given Length,  L = 10.5 ft = 126 in.            w = floor load               = 120 lb/ft2 = 0.8333…

Q: Q.2) For a T section beam with twolong wooden planks whose dimensions (all in mm) are shown in…

A:

Q: The beam shown in the figure is made of Wood that has an Allowable Shear Stress of 200 psi;…

A:

Q: Asimply supported wood beam that is 4,5 m long carries a 32 kN concentrated load at 8. The…

A:

Q: A beam is loaded as shown in the figure below and has a shape as shown in the figure (right).…

A: Given Data: F=200 lbs   To Find: (a) Maximum shear stress in the beam. (b) Shear stresses at point…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

A:

Q: I' B 150 mm C 100 mm B E D 30 mm 24 mm 24 mm

A: Here is the solution for the above question.Find centroid and moment of inertia of the section first

Q: 1) For the beam in the figure, determine the expressions for the distribution of internal shear…

A:

Q: A cantilever beam with a T-section is loaded by an inclined force of magnitude 6.5 kN(see figure),…

A:

Q: Cross section of a beam is shown in Figure 3. If a shear force V=100 kN is applied to the beam, find…

A:

Q: A beam is subjected to a distributed load and a concentrated force F (magnitude 400 N) at the end of…

A:

Q: A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 165 kN, acting as…

A:

Q: Q: Find the value of W which can be applied to the beam shown in figure below. if the maximum…

A: Consider the reaction at the supports RB and the reaction at supports C is Rc. Moment about C,…

Q: At an arbitrary cross-section, a - a the state of stress is obtained at various points (point 1 ~ 5,…

A:

Q: (a) Formulate the shear force function at section X-X of the beam, using a free body diagram. (b)…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: 120 KN 100 mm H 400 mm B 22m 150 mm Find the shear stress at point H on the beam. The wall thickness…

A:

Q: The internal shear force at a certain section of a steel beam is V = 185 kN. The beam cross section…

A: To findthe shear stress at point A, which is located at  below the centroid of the wide-flange…

Q: A wood pole of solid circular cross section (d = diameter) is subjected to a triangular distributed…

A: Calculated minimum required diameter bashed upon allowable bending stress and allowable shear…

Q: In the beam loading system given below, A is a simple and C is a sliding support. The outer diameter…

A:

Q: Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*.…

A: Find the shear stress at point M, N, O, P and draw stress distribution over the cross section