College Physics: A Strategic Approach (4th Edition)
4th Edition
ISBN: 9780134609034
Author: Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 8, Problem 5P
You’re carrying a 3.6-m-long, 25 kg pole to a construction site when you decide to stop for a rest. You place one end of the pole on a fence post and hold the other end of the pole 35 cm from its tip. How much force must you exert to keep the pole motionless in a horizontal position?
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule06:23
Students have asked these similar questions
You’re carrying a 3.6-m-long, 25 kg pole to a construction site when you decide to stop for a rest. You place one end of the pole on a fence post and hold the other end of the pole 35 cm from its tip. How much force must you exert to keep the pole motionless in a horizontal position?
A bench is made by placing a 3.9 meter long plank on two legs, each 0.36 meters from one of the plank's ends. The plank has a mass of 7.5 kg. If a box is placed on one of the ends of the plank, what is the maximum mass the box can have before it tips the bench over?
A 1.50x103 kg car, whose front is facing to the right (towards +x-axis) and whose engine is turned off
and in neutral, is held at rest on a frictionless ramp using a cable whose one end is attached to the car's
front at an angle 27.0° with respect to the ramp's surface. The other end of the cable is attached to a
wall perpendicular to the horizontal and the ramp is raised 30.0° above the horizontal. (Note: A free-
body diagram (FBD) is required in this problem)
(a) Find the force exerted by the ramp on the car's wheels.
(b) Find the tension on the cable.
(c) Suppose the wall where the other end of the cable was attached was replaced by a rotating
motor. If the car is now accelerating towards the peak of the ramp at 3.00 m/s2 due to the
rotating motor, how much tension is being exerted by the cable on the car?
Chapter 8 Solutions
College Physics: A Strategic Approach (4th Edition)
Ch. 8 - Prob. 1CQCh. 8 - Could a ladder on a level floor lean against a...Ch. 8 - Prob. 3CQCh. 8 - Prob. 4CQCh. 8 - Prob. 5CQCh. 8 - Prob. 6CQCh. 8 - Prob. 7CQCh. 8 - A spring exerts a 10 N force after being stretched...Ch. 8 - Prob. 9CQCh. 8 - A typical mattress has a network of springs that...
Ch. 8 - Take a spring and cut it in half to make two...Ch. 8 - A wire is stretched right to its breaking point by...Ch. 8 - Prob. 13CQCh. 8 - Prob. 14CQCh. 8 - Steel nails are rigid and unbending. Steel wool is...Ch. 8 - Two children hold opposite ends of a lightweight,...Ch. 8 - Prob. 19MCQCh. 8 - Prob. 20MCQCh. 8 - Prob. 21MCQCh. 8 - Prob. 22MCQCh. 8 - Prob. 23MCQCh. 8 - Prob. 24MCQCh. 8 - Prob. 25MCQCh. 8 - Prob. 26MCQCh. 8 - You have a heavy piece of equipment hanging from a...Ch. 8 - Prob. 1PCh. 8 - Prob. 2PCh. 8 - Prob. 3PCh. 8 - Prob. 4PCh. 8 - Youre carrying a 3.6-m-long, 25 kg pole to a...Ch. 8 - Prob. 6PCh. 8 - Prob. 7PCh. 8 - Prob. 9PCh. 8 - Prob. 11PCh. 8 - Prob. 13PCh. 8 - Prob. 14PCh. 8 - Prob. 15PCh. 8 - The stability of a vehicle is often rated by the...Ch. 8 - Prob. 18PCh. 8 - A car manufacturer claims that you can drive its...Ch. 8 - Prob. 20PCh. 8 - An orthodontic spring, connected between the upper...Ch. 8 - Prob. 22PCh. 8 - Experiments using optical tweezers measure the...Ch. 8 - Prob. 24PCh. 8 - One end of a 10-cm-long spring is attached to the...Ch. 8 - Prob. 26PCh. 8 - A spring has an unstretched length of 10 cm. It...Ch. 8 - A spring stretches 5.0 cm when a 0.20 kg block is...Ch. 8 - You need to make a spring scale to measure the...Ch. 8 - Prob. 30PCh. 8 - A force stretches a wire by 1.0 mm. a. A second...Ch. 8 - Prob. 32PCh. 8 - What hanging mass will stretch a 2.0-m-long,...Ch. 8 - An 80-cm-long, 1.0-mm-diameter steel guitar string...Ch. 8 - A mineshaft has an ore elevator hung from a single...Ch. 8 - The normal force of the ground on the foot can...Ch. 8 - A three-legged wooden bar stool made out of solid...Ch. 8 - Prob. 38PCh. 8 - Prob. 39PCh. 8 - Prob. 40PCh. 8 - A glass optical fiber in a communications system...Ch. 8 - The Achilles tendon connects the muscles in your...Ch. 8 - Prob. 44PCh. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 51GPCh. 8 - Prob. 52GPCh. 8 - Prob. 53GPCh. 8 - Prob. 55GPCh. 8 - Two identical, side-by-side springs with spring...Ch. 8 - Prob. 57GPCh. 8 - Prob. 58GPCh. 8 - Prob. 59GPCh. 8 - A 25 kg child bounces on a pogo stick. The pogo...Ch. 8 - Prob. 61GPCh. 8 - In the hammer throw, an athlete spins a heavy mass...Ch. 8 - There is a disk of cartilage between each pair of...Ch. 8 - Orb spiders make silk with a typical diameter of...Ch. 8 - Larger animals have sturdier bones than smaller...Ch. 8 - Prob. 67GPCh. 8 - Prob. 68GPCh. 8 - Prob. 69MSPPCh. 8 - Prob. 70MSPPCh. 8 - Prob. 71MSPPCh. 8 - Prob. 72MSPP
Additional Science Textbook Solutions
Find more solutions based on key concepts
Earth and Sun arc 8.33 light minutes apart. Event A occurs on Earth at time t = 0 and event B on the Sun at t =...
Essential University Physics (3rd Edition)
3. What is free-fall, and why does it make you weightless? Briefly describe why astronauts are weightless in th...
The Cosmic Perspective (8th Edition)
17. A speed skater moving to the left across frictionless ice at 8.0 m/s hits a 5.0-m-wide patch of rough ice....
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
70. * Robin Hood wishes to split an arrow already in the bull's-eye of a target 40 m away. If he aims directly ...
College Physics
Would you say the temperature stays approximately the same every month of the year at your location?
Lecture- Tutorials for Introductory Astronomy
You bring a 350-g wrench into the house from your car. The house is 15C warmer than the car, and it takes 2.52 ...
Essential University Physics: Volume 1 (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A 5.2-m ladder rests against a wall as shown. The ladder has a mass of 27.6 kg. A 56.3-kg person stands on the ladder at a distance of 3.6 m from the bottom of the ladder. The foot of the ladder is 1.9 m from the bottom of the wall. Assume there is no friction between the ladder and the wall so that the force of the wall on the ladder is acting only in the horizontal direction. However, there is a friction force between the ladder and the ground. 1.) What is the force, in N, exerted by the wall on the ladder?arrow_forwardA 4.8 m ladder rests against a wall as shown. The ladder has a mass of 26.4 kg. A 57.6 kg person stands on the ladder at a distance of 3.5 m from the bottom of the ladder. The foot of the ladder is 1.9 m from the bottom of the wall. Assume there is no friction between the ladder and the wall so that the force of the wall on the ladder is acting only in the horizontal direction. However, there is a friction force between the ladder and the ground. (a) What is the force, in N, exerted by the wall on the ladder? (b) What is the normal force, in N, exerted by the floor on the ladder? (c) What is the friction force, in N, between the ladder and the ground?arrow_forwardA 10 m long board has a mass of 7 kg. The left end of the board is against a wall and it sticks straight out like a boom. A rope is tied 1 m from the right end of the board and makes a 44 degree angle with the boom. A 25 kg box hangs 3 m from the right end. Find the tension in the rope.arrow_forward
- Scientists have studied how snakes grip and climb ropes. In one study, they found that an important characteristic of a rope is its “compliance”— that is, how easily the rope, while under tension, can be flexed. As shown how scientists measured a rope’s compliance by attaching it to two strings, each supporting an identical mass m. The strings contort the rope so that its middle section lies at angle θ. For θ = 30° and m = 100 g, what are the tensions T1 and T2 in the upper and middle parts of the rope?arrow_forwardPLEASEarrow_forwardA uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.877 m0.877 m and 1.23 kg1.23 kg , respectively. A force of constant magnitude ?F acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of ?F that will accelerate the rod from rest to an angular speed of 6.61 rad/s6.61 rad/s in 8.07 s8.07 s .arrow_forward
- A 20 kg dog stands on a 40 kg platform that is supported by two ropes. One rope is attached to the right edge of the platform and the other is attached 50 cm from the left edge of the platform. The dog sits 50 cm from the right edge of the platform. A 5.0 kg cat jumps up, but is wary of the dog abs stays all the way on the left edge. The platform is 2.0 m long. What is the tension in each rope?arrow_forwardWhen a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total gravitational force on the body, F, is supported by the force n exerted by the floor on the toes of one foot. A mechanical model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and e when F, = n = 675 N. (For e, enter the smaller of the two possible values between 0° and 90°.) Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm T = N R = N Need Help? Read Itarrow_forwardWhen a gymnast weighing 740 N executes the iron cross as in figure (a), the primary muscles involved in supporting this position are the latissimus dorsi ("lats") and the pectoralis major ("pecs"). The rings exert an upward force on the arms and support the weight of the gymnast. The force exerted by the shoulder joint on the arm is labeled F while the two muscles exert a total force F on the arm. Determine the magnitude of the force F Note that one ring supports half the weight of the gymnast, which is w 370 N as indicated in figure (b). Assume that the force F acts at an angle of 45° below the horizontal at a distance of 4.0 cm from the shoulder joint. In your estimate, take the distance from the shoulder joint to the hand to be L = 75 cm and ignore the weight of the arm. m kN Shoulder joint 4.0 cm- 45.00 Ed Bock/CORBISarrow_forward
- When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total gravitational force on the body, F, is supported by the force n exerted by the floor on the toes of one foot. A mechanical model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and 0 when F, = n = 720 N. (For 0, enter the smaller of the two possible values between 0° and 90°.) -Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm a T = R = N z z oarrow_forwardWhen a gymnast weighing 740 N executes the iron cross as in figure (a), the primary muscles involved in supporting this position are the latissimus dorsi ("lats") and the pectoralis major ("pecs"). The rings exert an upward force on the arms and support the weight of the gymnast. The force exerted by the shoulder joint on the arm is labeled Fs while the two muscles exert a total force Fm on the arm. Determine the magnitude of the force Fm. Note that one ring supports half the weight of the gymnast, which is w = 370 N as indicated in figure (b). Assume that the force Fm acts at an angle of 45° below the horizontal at a distance of 4.0 cm from the shoulder joint. In your estimate, take the distance from the shoulder joint to the hand to be L = 71 cm and ignore the weight of the arm.arrow_forwardThe uniform beam has a mass of 46 kg per meter of length. Determine the reactions at the supports. Answers: Ay A Bx = By = 659 i 1500 2.5 m N N ! N 1.1 m 220 kg Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Glencoe Physics: Principles and Problems, Student...
Physics
ISBN:9780078807213
Author:Paul W. Zitzewitz
Publisher:Glencoe/McGraw-Hill
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Static Equilibrium: concept; Author: Jennifer Cash;https://www.youtube.com/watch?v=0BIgFKVnlBU;License: Standard YouTube License, CC-BY