Concept explainers
The initial discharge rate of water via the pipe.
The time taken to empty the swimming pool.
The value of the friction factor.
Whether the minor loss is really minor or not.

Answer to Problem 155P
The discharge rate of water via the pipe is
The time taken to empty the swimming pool is
The given value of the friction factor is not accurate and the reasonable value of friction factor is
The value of minor loss is truly minor.
Explanation of Solution
Given information:
The swimming pool diameter is
The flow is incompressible and turbulent. The difference in elevation between the fountain and the pipe is null. The pressure at the inlet ad the exit is atmospheric in nature.
Write the expression to calculate the energy equation. Assume the effect of kinetic energy correction factor to be negligible.
Here, the inlet pressure is
Write the expression to calculate the exit velocity when time is
Here, he volume flow rate is
Write the expression for the area of cross section.
Here, the diameter of the pipe is
Substitute
Write the expression to calculate the head loss.
Here, the diameter of the pipe is
Write the expression for the elevation at any given time.
Here, the coefficient of minor loss is
Write the expression for the flow rate at any time given.
Substitute
Write the expression to calculate the water amount flowing b=via the pipe for a differential time.
Here, the differential time is
Substitute
Write the expression for the area of the tank.
Here, the diameter of the tank is
Write the expression for the decrease of volume of water in the swimming pool.
Here, the negative change in datum of tank is
Substitute
Integrate Equation (XIII) from
Write the expression to calculate the Reynolds number.
Here, the viscosity of the fluid is
Write the expression for the Colebrook equation.
Here, the friction factor is
Calculation:
Refer to Table A-3, "Properties of saturated water" to obtain the value of
The flow is fully developed making the roughness of the plastic null.
Substitute
Substitute
Consider the time is zero.
Substitute
Substitute
Convert
Substitute
Substitute
Substitute
Substitute
Hence, the value of the minor loss is truly minor as the friction factor remains unchanged.
Conclusion:
The discharge rate of water via the pipe is
The time taken to empty the swimming pool is
The given value of the friction factor is not accurate and the reasonable value of friction factor is
The value of minor loss is truly minor.
Want to see more full solutions like this?
Chapter 8 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
- 1. The rotating steel shaft is simply supported by bearings at points of B and C, and is driven by a spur gear at D, which has a 6-in pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA =3000 lbĘ in. The shaft is machined from steel with Sy=60kpsi and Sut=80 kpsi. (1) Draw a shear force diagram and a bending moment diagram by F. According to your analysis, where is the point of interest to evaluate the safety factor among A, B, C, and D? Describe the reason. (Hint: To find F, the torque Tд is generated by the tangential force of F (i.e. Ftangential-Fcos20°) When n=2.5, K=1.8, and K₁ =1.3, determine the diameter of the shaft based on (2) static analysis using DE theory (note that fatigue stress concentration factors need to be used for this question because the loading condition is fatigue) and (3) a fatigue analysis using modified Goodman. Note) A standard diameter is not required for the questions. 10 in Darrow_forward3 N2=28 P(diametral pitch)=8 for all gears Coupled to 25 hp motor N3=34 Full depth spur gears with pressure angle=20° N₂=2000 rpm (1) Compute the circular pitch, the center-to-center distance, and base circle radii. (2) Draw the free body diagram of gear 3 and show all the forces and the torque. (3) In mounting gears, the center-to-center distance was reduced by 0.1 inch. Calculate the new values of center-to-center distance, pressure angle, base circle radii, and pitch circle diameters. (4)What is the new tangential and radial forces for gear 3? (5) Under the new center to center distance, is the contact ratio (mc) increasing or decreasing?arrow_forward2. A flat belt drive consists of two 4-ft diameter cast-iron pulleys spaced 16 ft apart. A power of 60 hp is transmitted by a pulley whose speed is 380 rev/min. Use a service factor (Ks) pf 1.1 and a design factor 1.0. The width of the polyamide A-3 belt is 6 in. Use CD=1. Answer the following questions. (1) What is the total length of the belt according to the given geometry? (2) Find the centrifugal force (Fc) applied to the belt. (3) What is the transmitted torque through the pulley system given 60hp? (4) Using the allowable tension, find the force (F₁) on the tight side. What is the tension at the loose side (F2) and the initial tension (F.)? (5) Using the forces, estimate the developed friction coefficient (f) (6) Based on the forces and the given rotational speed, rate the pulley set. In other words, what is the horse power that can be transmitted by the pulley system? (7) To reduce the applied tension on the tight side, the friction coefficient is increased to 0.75. Find out the…arrow_forward
- The tooth numbers for the gear train illustrated are N₂ = 24, N3 = 18, №4 = 30, №6 = 36, and N₁ = 54. Gear 7 is fixed. If shaft b is turned through 5 revolutions, how many turns will shaft a make? a 5 [6] barrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forward
- CE-112 solve this problem step by step and give me the correct answer pleasearrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningInternational Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L




