1.5 m B. -0.333 m

Q: Two blocks are connected by a solid strut attached to each block with frictionless pins. If the…

A: Given : To find : Maximum weight of A to maintain equilibrium

Q: 3. Determine the smallest horizontal force P that would push the homogenous cylinder of weight W…

A: As per given question  We have to find force required to puah the cylinder

Q: 2.5 m 4 m 30° 90° 90 00 N

A:

Q: The system shown is in static equilibrium and motionless. The force "P" Is at the maximum magnitude…

A: NOTE - As per our company guidelines we are allowed to answer only the first three sub-parts. Kindly…

Q: Answer with proper explanations.

A: The free body diagram for the lighter block is given below,   The force equilibrium in y-direction,…

Q: Determine the maximum downward force Pmax that can be applied to wedge A that wil keep the assembly…

A: Given: The weight of block C, W = 192 N

Q: What is the maximum force F that will maintain static equilibrium? Assume the coefficient of…

A: N1=mg=10(9.8)=98NN2=17(9.8)=166.6N

Q: The cylinder shown is homogeneous and has a mass of 30 kg. If slipping of the cylinder is prevented…

A: Draw the free body diagram for the above problem.

Q: 20 cm Q5: The homogeneous block weights 250 N. Determine the value of P for which the block 30 cm in…

A: Given Weigh of the block = 250 N Coefficient of friction = 0.3 Applied load = 10 N To find Magnitude…

Q: Determine whether the block shown in the figure is in equilibrium and find the magnitude and…

A: Draw a free-body diagram of the block.From the diagram, it is clear that the block is in…

Q: Problem 4. Determine the smallest force P that must be applied to the 150-lb uniform crate to cause…

A:

Q: The designers of lamp mechanisms, such as that shown in the figure, usually rely on joint friction…

A: Given:Mass, m = 0.65 kgDiagram is givenTo find:Spring force Fs

Q: the homogeneous cylinder of weight W=100 N rests in a frictionless right angled corner. determine…

A:

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A:

Q: Weight of the refrigerator is 880 N. The coefficient of static friction is 0.22 for all surfaces.…

A:

Q: Determine whether the block shown is in equilibriumand find the magnitude and direction of the…

A: Draw the free body diagram of the body.

Q: Can the system in Figure .(4) be in static equilibrium in the position shown? The uniform bar AB (…

A: Consider the free body diagram of the rod.

Q: Q4.A. An effort F is required just to move a certain body of weight 393 N up an inclined plane of…

A: Since you have uploaded two questions and did not specify which question to be solved, as per the…

Q: What is the magnitude of the force on the pin at point C? (include units with answer) А. What is the…

A:

Q: The homogeneous 300-kg cylinder is pulled over the 100-mm step by the horizontal force P. Find the…

A: for un-equilibrium conditions the moment due to the force P about the pivot should be greater than…

Q: The figure below are two discs D and E which have a mass of 200 lbs and 100 lbs, respectively. If P…

A:

Q: Determine the range of weights W for which the 111-lb block is in equilibrium. All wheels and…

A:

Q: Q4: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T = 60 N =30 N are…

A: Given that, mass of the box is 40 kg. The box is subjected to T = 60 N and F = 30 N forces.…

Q: The mass center G of the 1540-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: Q4: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T=60 N and F =30 N…

A:

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

A:

Q: The uniform bar is at rest on a smooth half-sphere with radius R = b / 2. In A there is a ball joint…

A:

Q: Determine a general expression for the normal force NA exerted by the smooth vertical wall on the…

A: The mass of cylinder is .The mass of bar is .

Q: The mass center G of the 1300-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: age 111 Practice Problem 4.8: If we double the mass of the chain, what are the new values for e…

A: Given                        Initial Mass, m1 = 10 kg Final mass (after doubled), m2 = 20 kg…

Q: The coefficient of friction between the 120 lb block (shown in figure below) and the incline plane…

A:

Q: 1. The cylinder of weight, W (see the table of values), shown below is being hoisted up with the…

A:

Q: What additional force must be added to the hook at A for it to be in static equilibrium? Express…

A:

Q: The uniform 16-kg plate is welded to the vertical shaft, which is supported by bearings A and B.…

A:

Q: The 18-lb box shown is attached to a spring that has a k=2 lb/in and an unstretched length of 14…

A:

Q: Cable AB passes over the small ideal pulley Cwithout a change in its tension. What length of cable…

A:

Q: The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and…

A: Initially, we will disassemble the apparatus and create the conveyor's free-body diagram.The baggage…

Q: Determine whether the block shown is in equilibriumand find the magnitude and direction of the…

A: Draw free-body diagram of the block.     From the diagram, it is clear that block is in…

Q: The bars shown are the same length. The spring is unstretched when alpha= 90°; the horizontal…

A: Consider the diagram as shown below.

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.