Chapter 7, Problem 7.12Q

: + ♡ +① العنوان I need a detailed drawing with explanation so A 4 ined sove in peaper 96252 Example 5.5 The turbine rotor of ship has a mass of 30 tons, a radius of gyration of 600 mm and rotates at 2400 rpm ia clockwise direction when viewed from aft. The ship pitches through a total angle of 7.5° above and 7.5° below the horizontal, the motion beingle harmonic and hav gyroscopic couple on the bow rises. ding down be a period of 12 sec. Determine the maximum of the turbine and the direction of yaw as bax r 2.01 ۳/۱

88 L Solle ined sove in peaper 96252 Example 5.5 The turbine rotor of a ship has a mass of 30 tons, a radius of gyration of 600 mm and rotates at 2400 rpm in a clockwise direction when viewed from aft. The ship pitches through a total angle of 15%, 7.5° above and 7.5° below the horizontal, the motion being simple harmonic and having a period of 12 sec. Determine the maximum gyroscopic couple on the holding down bolts of the turbine and the direction of yaw as the bow rises. النص ملصقات -20125 750 31 الرسم X 7.0! 989 C

L + ined sove in peaper X-P 96852 Example 5.5 The turbine rotor of a ship has a mass of 30 tons, a radius of gyration of 600 mm and rotates at 2400 rpm in a clockwise direction when viewed from aft. The ship pitches through a total angle of 15%, 7.5° above and 7.5° below the horizontal, the motion being simple harmonic and having a period of 12 sec. Determine the maximum gyroscopic couple on the holding down bolts of the turbine and the direction of yaw as the bow rises. -20125 750 x2.01

Example 5.5 The turbine rotor of a ship has a mass of 30 tons, a radius of gyration of 600 mm and rotates at 2400 rpm in a clockwise direction when viewed from aft. The ship pitches through a total angle of 15%, 7.5° above and 7.5° below the horizontal, the motion being simple harmonic and having a period of 12 sec. Determine the maximum gyroscopic couple on the holding down bolts of the turbine and the direction of yaw as the bow rises.

Please explain each step, writing euler rates etc

5. (计算题) Calculate the DOF of following mechanisms. If there are compound hinge, passive DOF or Redundant Constraint, please point them out. 品 ⑤A (a) 凸轮拨杆机构

6.(计算题) Calculate the DOF of following mechanisms. If there are compound hinge, passive DOF or Redundant Constraint, please point them out. E D A B C F

A hot surface at 150°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m-K) to it, with a center- to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m²K. Determine the rate of heat transfer from the surface for a 1-m × 1-m section of the plate. Also determine the overall effectiveness of the fins. 0.6 cm 0.25 cm The total rate of heat transfer is kW. The fin effectiveness is

Consider a stainless steel spoon (k = 8.7 Btu/h·ft·°F) partially immersed in boiling water at 200°F in a kitchen at 75°F. The handle of the spoon has a cross section of 0.08 in × 0.5 in and extends 7 in in the air from the free surface of the water. The heat transfer coefficient at the exposed surfaces of the spoon handle is 3 Btu/h·ft2·°F.   NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.  A spoon is placed inside the container, such that the distance of the water level from the top end of the handle of the spoon is 7 meters. T sub air is indicated in the region outside the container.       Identify the assumptions required to solve the problem.   Check All That Apply One-dimensional heat transfer analysis is used to solve the problem. One-dimensional heat transfer analysis is used to solve the problem. Bi-dimensional heat transfer analysis is used to solve the problem. Bi-dimensional heat transfer analysis is…