EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 9780100793439
Author: KALPAKJIAN
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 7, Problem 62SDP
To determine
Repeat Problem 7.61 for the curves shown in Fig. 7.12.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The membrane analogy does not apply to the hollow cross-sections considered in
Chapter 3 (non-circular twisting). Give an example that clearly shows that it fails and
explain why.
Consider the extrusion of a cylindrical billet, and compute the following.
Assume the starting billet to have a length of 0.3m and a diameter of 15cm. This is extruded into a cylindrical product that is 3cm in diameter and 7.5cm long. Neglecting the areas on the two ends, compute the ratio between the product surface area (wraparound cylinder) and the surface area of the starting billet. How would this ratio change if the product were a square with the same corss-sectional area as that of the 3cm diameter circle?
• In a sheet metal forming press the shape to be formed is
hemispherical cup of radius 15 cm in 2mm thick mild steel sheet.
The force required to deform sheet is 8 kN. The forming hammer
should approach job from a distance of 30 cm. The production rate
required is 240 components/hr. Calculate and suggest the
following specifications of the various hydraulic components used:
a) Hydraulic cylinder (bore & length)
b) Pump pressure and flow rate
c) Electric motor HP considering 75% pump efficiency
d) Reservoir size
e) Size of pump inlet and discharge tubing
Chapter 7 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 7 - Summarize the important mechanical and physical...Ch. 7 - What are the major differences between the (a)...Ch. 7 - List properties that are influenced by the degree...Ch. 7 - What is the difference between condensation...Ch. 7 - Explain the differences between linear, branched,...Ch. 7 - What is the glass-transition temperature?Ch. 7 - List and explain the additives commonly used in...Ch. 7 - What is crazing?Ch. 7 - What are polyblends?Ch. 7 - List the major differences between thermoplastics...
Ch. 7 - What is an elastomer?Ch. 7 - What effects does a plasticizing agent have on a...Ch. 7 - Define the following abbreviations: PMMA, PVC,...Ch. 7 - Explain why it would be advantageous to produce a...Ch. 7 - What are the differences and similarities of...Ch. 7 - Are molecular weight and degree of polymerization...Ch. 7 - Why do polymers need to be dried before...Ch. 7 - What characteristics of polymers make them...Ch. 7 - Do polymers strain harden more than metals or vice...Ch. 7 - Inspect various plastic components in an...Ch. 7 - Give applications for which flammability of...Ch. 7 - What characteristics make polymers advantageous...Ch. 7 - What properties do elastomers have that...Ch. 7 - Do you think that the substitution of plastics for...Ch. 7 - Is it possible for a material to have a hysteresis...Ch. 7 - Observe the behavior of the specimen shown in Fig....Ch. 7 - Add more to the applications column in Table 7.3.Ch. 7 - Discuss the significance of the glass-transition...Ch. 7 - Prob. 29QLPCh. 7 - Explain how cross-linking improves the strength of...Ch. 7 - Describe the methods by which the optical...Ch. 7 - How can polymers be made to conduct electricity?...Ch. 7 - Explain the reasons for which elastomers were...Ch. 7 - Give several examples of plastic products or...Ch. 7 - Describe your opinions regarding the recycling of...Ch. 7 - Explain how you would go about determining the...Ch. 7 - Compare the values of the elastic modulus, given...Ch. 7 - Why is there so much variation in the stiffness of...Ch. 7 - Explain why thermoplastics are easier to recycle...Ch. 7 - Give an example where crazing is desirable.Ch. 7 - Describe the principle behind shrink wrapping.Ch. 7 - List and explain some environmental pros and cons...Ch. 7 - List the characteristics required of a polymer for...Ch. 7 - How can you tell whether a part is made of a...Ch. 7 - As you know, there are plastic paper clips...Ch. 7 - By incorporating small amounts of a blowing agent,...Ch. 7 - In injection-molding operations (Section 19.3), it...Ch. 7 - From an environmental standpoint, do you feel it...Ch. 7 - Calculate the areas under the stressstrain curve...Ch. 7 - Prob. 50QTPCh. 7 - Prob. 51QTPCh. 7 - Estimate the number of molecules in a typical...Ch. 7 - Using strength and density data, determine the...Ch. 7 - Prob. 54QTPCh. 7 - Prob. 55SDPCh. 7 - Describe the design considerations involved in...Ch. 7 - Assume that you are manufacturing a product in...Ch. 7 - Assume you work for a company that produces...Ch. 7 - Prob. 59SDPCh. 7 - Make a list of products or parts that currently...Ch. 7 - Prob. 61SDPCh. 7 - Prob. 62SDPCh. 7 - Prob. 63SDPCh. 7 - Prob. 64SDPCh. 7 - With Table 7.3 as a guide, inspect various...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.arrow_forwardPlease solve in 10 minarrow_forwardExplain what is the effective-slenderness ratio?arrow_forward
- 3. A dimension of 225.00 mm is specified for a particular injection moulded component manufactured in ABS. Calculate the corresponding dimension to which the mould cavity should be machined, using the value of shrinkage given in the table below. Typical values of shrinkage for moldings of selected thermoplastics. Shrinkage, mm/mm (in/in) Shrinkage, Plastic Plastic mm/mm (in/in) ABS Polyethylene Polystyrene 0.006 0.025 Nylon-6,6 Polycarbonate 0.020 0.004 0.007 PVC 0.005arrow_forwardA typical plastic shopping bag made by blown film has a lateral dimension (width) of 550 mm. Assume the tube is expended from 1.5 to 2.5 times the extrusion die diameter. Calculate the extrusion die diameter size.arrow_forwardMay I have help with this please?arrow_forward
- A 10 mm thick plate is rolled to 7 mm thick in a rolling mill using 1000 mm diameter rigid rolls. The neutral point is located at an angle of 0.3 times the bite angle from the exit. What will be the thickness of the plate at the neutral point.arrow_forward6arrow_forward1. In the manufacture of automotive-body panels from carbon-steel sheet, stretcher strains (Lueders bands) are observed, which detrimentally affect surface finish. How can stretcher strains be eliminated? Explain with appropriate sketches. Also discuss how wrinkles in a deep drawing operation can be eliminated.arrow_forward
- Consider the extrusion of a cylindrical billet. Assume the billet to have a length of 0.3m and a diameter of 0.15m. This is extruded into a cylindrical product that is 0.03m in diameter and 7.5m long (a reduction ratio of 25). Neglecting the areas on the two ends, compute the ratio between the product surface area (wraparound cylinder) and the surface area of the starting billet. How would this ratio change if the product were a square with the same cross-sectional area as that of the 0.03m diameter circle?arrow_forwardA paper clip is made of wire 0.7 mm in diameter. If the original material from which thewire is made is a rod 25 mm in diameter, calculate the longitudinal engineering and truestrains that the wire has undergone during processing.arrow_forwardA tube of 12 mm external diameter and 1mm thickness is to be reduced to 16 mm external diameter and 0.5 mm thickness. The die angle is 24º and plug angle is 16º. The coefficients of friction at die and tube interface and tube and plug (mandrel) interface is 0.5. The flow stress of tube material is 340 N/mm2 . The tube drawing is carried at a speed of 0.4 m/s. Calculate the fixed plugarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Relationship Between Elastic Constants and Connecting Equations; Author: Engineers Academy;https://www.youtube.com/watch?v=whW5PnM7Pug;License: Standard Youtube License