Timer: Timer is mainly used to keep an output ON for a specific length of time. It provides a preset delay to the control actions. In a timer, the output will be energized when the preset value becomes equal to the accumulated value. Three different types of timers include a Delay-OFF, a Delay-ON, and a Delay-ON-Retentive timer. Timer OFF Delay (TOF): TOF refers to an off-delay timer. TOF counts the time-based intervals as soon as the instruction becomes false. Here, the output changes its state from high to low when the timer provides some time delay (instruction goes from ON to OFF state). Given: In the given figure, the tags are formed for various areas of controller for various purposes. The two push buttons are used to start and stop the process. The highest level of the tank is indicated by the full level sensor switch. Here, when the tank level is full, the switch gets closed. The empty level of the tank is indicated by the empty level sensor switch. Here, when the tank starts the filling process, the switch gets closed. The “Solenoid A” is used to de-energize (it means to fill) the tank. The “Solenoid B” is used to energize (it means to empty) the tank.

Question

Want to see the full answer?

Answer 1

Question

Chapter 7, Problem 13P

Program Plan Intro

Timer:

Timer is mainly used to keep an output ON for a specific length of time.

It provides a preset delay to the control actions.

In a timer, the output will be energized when the preset value becomes equal to the accumulated value.

Three different types of timers include a Delay-OFF, a Delay-ON, and a Delay-ON-Retentive timer.

Timer OFF Delay (TOF):

TOF refers to an off-delay timer.

TOF counts the time-based intervals as soon as the instruction becomes false.

Here, the output changes its state from high to low when the timer provides some time delay (instruction goes from ON to OFF state).

Given:

In the given figure, the tags are formed for various areas of controller for various purposes.

The two push buttons are used to start and stop the process.

The highest level of the tank is indicated by the full level sensor switch. Here, when the tank level is full, the switch gets closed.

The empty level of the tank is indicated by the empty level sensor switch. Here, when the tank starts the filling process, the switch gets closed.

The “Solenoid A” is used to de-energize (it means to fill) the tank.

The “Solenoid B” is used to energize (it means to empty) the tank.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

After playing our giving implementation, your task is to implement Dinning Philosophers with semaphore in C, by including and Your implementation will require creating five philosophers, each identified by a number 0.4. Each philosopher will run as a separate thread. Create threads using Pthreads as discussed in the Lecture slides on Chapter 4 and Practice Lab on Threads. Your solution needs to accomplish the following: Implement in C (15 points) 1. dp1.c - You are to provide your solution to this assignment as a single C program named 'dp1.c using semaphore. Explain in you code (as comments) that the dead lock will happen or not. If there is a possible deadlock, you can simply solve the deadlock by pick the fork in order like the first solution in our slides. Solve Deadlock by Footman (15 points) 1. Here is a new solution to overcome the deadlock. The Dining Philosophers decide to hire a footman whose task to allow only four philosophers to sit on the table. When entering and…

8.4 Self-Bias Configuration 20. Determine Zi. Zo. and A,, for the network of Fig. 8.73 if gf, = 3000 μS and gos = 50 μs. 21. Determine Z, Zo, and A, for the network of Fig. 8.73 if the 20-uF capacitor is removed and the parameters of the network are the same as in Problem 20. Compare results with those of Problem 20. +12 V 3.3 ΚΩ HE C₂ Vo Z Zo C₁ 10 ΜΩ Z₁ 1.1 ΚΩ Cs 20 µF FIG. 8.73 Problems 20, 21, 22, and 59.

21. Determine Zi, Zo, and A, for the network of Fig. 8.73 if the 20-μF capacitor is removed and the parameters of the network are the same as in Problem 20. Compare results with those of Problem 20. +12 V 3.3 ΚΩ +6 C₂ C₁ Z₁ 10 ΜΩ 1.1 ΚΩ Cs 20 μF FIG. 8.73 Zo