Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 8SQ
Select the best answer for each of the following.
Most push buttons are
- a. momentary contact.
- b. single contact.
- c. double contact.
- d. a combination.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Sketch the electronic symbol (schematic) for the following components/ devices. Briefly
describe the function of the electronic component and use the IEEE/ANSI standard symbol
as indicated below.
IEEE/ANSI Standard Symbol
Component
1. Normally Open
(Momentary)
Function
Push Button
Switch
2. Normally
Closed
(Momentary)
Push Button
Switch
3. SPST Switch
4. SPDT Switch
5. DPST Switch
6. DPDT Switch
7. Fixed Resistor
8. Any Variable
Resistor
9. Polarized
Сарacitor
10. Non-Polarized
Capacitor
11. Any Variable
Сарacitor
12. Inductor
5- Design and sketch a MOD-8 ripple-counter with manual reset push button.
9-
Controlled variable is the output of
a.
Plant
b.
Controller
c.
None of the above
d.
Error Detector
Chapter 6 Solutions
Electric Motor Control
Ch. 6 - What is meant by normally open contacts and...Ch. 6 - Why is it that normally open and normally closed...Ch. 6 - How are colored pilot lights indicated in wiring...Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....Ch. 6 - Select the best answer for each of the following....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 15 - Which of the following is not one of the advantages of the inductive proximity sensor over the limit switch? A) It is small in size.B) They can be used in potentially explosive places.C) They make contact perception.D) It has no moving parts.E) There is no contact problem.arrow_forward1What is the condition of a one-way switch if it has no resistance between terminals at both toggle positions 1 & 2? Is it still usable or not? Explain. 2 A one-way switch is in ON position if its resistance between terminals is almost zero. Explain. 3. Can a push button switch be used to control a lamp? Explain. 4. Identify the ON and OFF positions of the MCB. 5. A bulb or lamp is busted or broken if its resistance is less than 100Q. True or False?arrow_forwardthe controlled signals in control BD are then going to Select one: a. actuators b. sensors C. plant d. controllers the actuator requires a much higher primary voltage than 150v is Select one: O a Capacitive Discharge Ignition (CDI) O b. Inductive (Smart) O C. Peak and Hold O d. Inductive (Dumb)arrow_forward
- I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?arrow_forwardComputer Digital Logic. Design 4 X 1 Multiplexer. Handdrawn will work.arrow_forwardAll questions solve or skip i will dislike if not solve all Use Keybordarrow_forward
- A circuit has two pushbutton switches connected to pin PB2and PB3 and two LEDs connected to pin PC0 and PC1 of AVR ATmega16 microcontroller. Write a program to control the LEDs as when any pushbutton pressedthe two LEDs will blink at the same time with 800ms total delay time for every blink.arrow_forward1. Fill-in the blanks with the correct answer or chose the correct answer. the blue wire 1-3. Given a 3-wire NPN inductive sensor, the black wire is to be connected to the and the brown wire to the to the 4. After connecting the load to an NPN sensor, the other terminal of the load will be connected to the 5. If a PLC, serving as load, uses a sinking input card, it needs a (PNP/NPN) proximity sensor. 6. Capacitive, Inductive, Photo electric sensors are called proximity sensors becausearrow_forwardWhat are the functions of a sensor? Explain the function of on delay timers. Explain the working principle of a limit switch. Differentiate the behavior of on delay timer and off delay timer. Refer to the timing diagram.arrow_forward
- D Question 32 The diagram shown is that of a L1 Pressure switch Manual pushbutton 120 VAC Temperature switch O hardwired relay schematic. ladder logic program. O input module schematic. O output module schematic. M Motor starter coil OL L2arrow_forwardDAC's could be implemented using current switches. Explain the operation and characteristics of such types.arrow_forwardDigital system Please do explain how the state diagram worksarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Latches and Flip-Flops 1 - The SR Latch; Author: Computer Science;https://www.youtube.com/watch?v=-aQH0ybMd3U;License: Standard Youtube License