Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
9th Edition
ISBN: 9781285180014
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 6RQ
What do the terms normally open and normally closed refer to with regard to a switch or set of contacts? Draw a normally open and normally closed contact.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The diagram shows a brass rod and an iron rod beside each other at the bottom of a
rectangular coil. What happens when a d.c. current passes through the coil?
to d.c.
supply
rectangular
coil
brass
iron
rod
rod
Only the brass rod is magnetized
Only the iron rod is magnetized
The two rods attract each óther
The two rods repel each other.
23. Draw the following symbols:
a. double acting, momentary contact push button.
b. normally open pressure switch
C. current transformer.
d. Normally closed float switch.
e. normally open limit switch.
F. normally closed switch.
Explain with a diagram how the bimetallic temperature switch is use to measure
Chapter 5 Solutions
Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
Ch. 5 - What are the three types of electrical diagrams...Ch. 5 - A load is an electrical device that __________. a....Ch. 5 - What is the major load of an air-conditioning...Ch. 5 - Identify the following symbols for loads:Ch. 5 - Prob. 5RQCh. 5 - What do the terms normally open and normally...Ch. 5 - What is the difference between a magnetic starter...Ch. 5 - Prob. 8RQCh. 5 - Draw a heating and a cooling thermostat and...Ch. 5 - A three-pole contactor would allow how many paths...
Ch. 5 - A disconnect switch is used to __________. a. open...Ch. 5 - What determines whether a pressure switch opens or...Ch. 5 - Identify the following symbols for...Ch. 5 - What is the difference between a thermal overload...Ch. 5 - What is the purpose of a transformer? Draw the...Ch. 5 - Which of the following is not a requirement for an...Ch. 5 - What is the purpose of a legend on a schematic...Ch. 5 - A factual diagram is _____. a. a pictorial diagram...Ch. 5 - Identify the following symbols for safety devices.Ch. 5 - Prob. 20RQCh. 5 - True or False: The schematic diagram tells service...Ch. 5 - What is the difference between a pilot duty and a...Ch. 5 - What type of switch would be used to open or close...Ch. 5 - What is the purpose of a fuse in an electrical...Ch. 5 - True or False: A solenoid valve is a device that...Ch. 5 - What is a signal light used for in a control...Ch. 5 - Change the following normally open elements from...Ch. 5 - Draw the symbols for the following electrical...Ch. 5 - Add letter designations to the symbols to indicate...Ch. 5 - Draw a symbol for a magnetic starter.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pressure switch is to be installed in a circuit that requires it to have three normally open contacts and one normally closed contact. The switch actually has one normally open Contact What must be done to permit this pressure switch to operate in this circuit?arrow_forwardWhy are the contacts of a micro switch spring loaded?arrow_forwardWhat pin numbers are connected to the coil of an 8-pin control relay?arrow_forward
- What is the primary use of a limit switch?arrow_forwardRefer to Figure 21–1 to answer the following questions. In what position must switch SW 123 be set to make connection between terminals 3 and 4?arrow_forwardAn 11-pin control relay contains three sets of single-pole double throw contacts. List the pin numbers by pairs that can be used as normally open contacts.arrow_forward
- Explain the difference between auxiliary contacts and load contacts.arrow_forwardReferring to the circuit in Figure 2–33, should the float switch be connected as a normally open or normally closed switch?arrow_forwardRefer to Figure 211 to answer the following questions. Referring to switch (RS SW 123), in what position must the switch be set to make connection between terminals 3 and 4?arrow_forward
- To answer the following questions refer to the circuit in Figure 416. The pressure switch is shown as: a. Normally open b. Normally closed c. Normally open held closed d. Normally closed held openarrow_forwardWhat is a normally dosed switch?arrow_forwardRefer to the schematic in Figure 7-10. Assume that when the START button is pressed, the control transformer fuse blows. What is the most likely cause of this trouble? Figure 7-10 Numbers are placed beside all components.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License