5.5-12 A small dam of height h = 2.0 m is constructed of vertical wood beams AB of thickness t = 120 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. Determine the maximum bending stress omax in the beams, assuming that the weight density of water is y = 9.81 kN/m³. h

5.5-12 A small dam of height h = 2.0 m is constructed of vertical wood beams AB of thickness t = 120 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. Determine the maximum bending stress omax in the beams, assuming that the weight density of water is y = 9.81 kN/m³. h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pontoon bridge (see figure) is constructedof two longitudinal wood beams, known as balks,that span between adjacent pontoons and supportthe transverse floor beams, which are called chesses.For purposes of design, assume that a uniform floorload of 7.5 kPa acts over the chesses. (This loadincludes an allowance for the weights of the chessesand balks.) Also, assume that the chesses are 2.5 m long and that the balks are simply supported with aspan of 3.0 m. The allowable bending stress in thewood is 15 MPa.(a) If the balks have a square cross section, what istheir minimum required width bmin?(b) Repeat part (a) if the balk width is 1.5 b andthe balk depth is b; compare the cross-sectionalareas of the two designs.
A beam having a cross section in the formof a channel (see figure) is subjected to a bendingmoment acting about the z axis.Calculate the thickness t of the channel in orderthat the bending stresses at the top and bottom of thebeam will be in the ratio 7:3, respectively.
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 16 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 1 m. i) Reaction force at B = ii) Reaction Force at A = iii) The distance from B at which the shear Force value changes from "-" to "+" = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
5.5-13 Determine the maximum tensile stress o, (due to pure bending about a horizontal axis through C by positive bending moments M) for beams having cross sections as follows (see figure). (a) A semicircle of diameter d (b) An isosceles trapezoid with bases b¡ = b and b2 = 4b/3, and altitude h (c) A circular sector with a = m/3 and r = d/2 %3D |y C Xc a (a) (b) (c)
A horizontal beam of length 4 m and mass 9.0 kg has a mass of 3.0 kg and width 0.8 m sitting at the end of the beam (see the following figure). What is the torque due to gravity (in N m) on the beam-block system about the support at the wall? (Enter the magnitude.) Wall support 0.8 m, 3.0 kg 4 m, 9.0 kg N-m
During construction of a highway bridge, the main girders are cantilevered outward from one pier toward the next (see figure). Each girder hasa cantilever length of 48 m and an I-shaped cross section with dimensions shown in the figure. The load on each girder (during construction) is assumed to be 9.5 kN/m, which includes the weight of the girder. Determine the maximum bending stress in a girder due to this load.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. note ; Please solve number 3.4.5.6.7 i) Reaction force at B = 33.4N ii) Reaction Force at A = 18.6N iii) The distance from B at which the shear Force value changes from "-" to "+" = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
Q2/ A beam with two overhang carries a uniform load of intensity w N/m, and support as shown in figure below. Determine the maximum permissible value of load w N/m. Given: the allowable tensile and compressive stress of 20Mpa. The beam has a rectangular cross section area with high-50mm and width=100mm 1m w N/m 2.5m 1-3 B 1m
A tapered cantilever beam AB of length L hassquare cross sections and supports a concentratedload P at the free end (see figure part a). The widthand height of the beam vary linearly from hA at thefree end to hB at the fixed end.Determine the distance x from the free end A to thecross section of maximum bending stress if hB = 3hA.(a) What is the magnitude σmax of the maximumbending stress? What is the ratio of the maximumstress to the largest stress B at the support?(b) Repeat part (a) if load P is now applied as a uniformload of intensity q = P/L over the entirebeam, A is restrained by a roller support, andB is a sliding support (see gure part b).
4.5-11 The simple beam AB supports a uniform load of intensity q = 10 lb/in. acting over one-half of the span and a concentrated load P = 80 lb acting at midspan (see figure). Draw the shear-force and bending-moment diagrams for this beam. A |--1/2 = PROB. 4.5-11 = 40 in. P = 80 lb q=10 lb/in. L 12/2 = = 40 in. B