**Educational Content: Calculating Maximum Bending Stress in Dam Beams****Problem Statement:**A small dam of height \( h = 1.2 \, m \) is constructed of vertical wood beams \( AB \) with a thickness \( t = 113 \, mm \), as shown in the adjacent figure. **Figure Description:**- The diagram shows a vertical cross-section of the dam with a height \( h \).- The wood beam \( AB \) is illustrated on the right, with water exerting pressure from the left side.- The thickness of the beams is indicated as \( t \).- Supports at the top and bottom of the dam are depicted, implying simply supported beams.**Task:**Consider the beams to be simply supported at the top and bottom.Determine the maximum bending stress \( \sigma_{\text{max}} \) (in MPa) in the beams, assuming the weight density of water is \( \gamma = 9.81 \, \text{kN/m}^3 \). (Enter the magnitude.)**Input Box:**[ ______ ] MPa---By properly solving the problem, students will gain insights into fluid statics, structural analysis, and application of material mechanics principles.

Answered: Image /qna-images/answer/9e044a68-96d5-4828-a8a2-e1234fa9c2ff.jpg

small dam of height h = 1.2 m is constructed of vertical wood beams AB of thickness t = 113 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. etermine the maximum bending stress max (in MPa) in the beams, assuming that the weight density of water is y = 9.81 kN/m³. (Enter the magnitude.) MPa

small dam of height h = 1.2 m is constructed of vertical wood beams AB of thickness t = 113 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. etermine the maximum bending stress max (in MPa) in the beams, assuming that the weight density of water is y = 9.81 kN/m³. (Enter the magnitude.) MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply supported wooden I beam AB (shown below) is loaded by the distributed force q-18 kN/m. If the length of the beam is L-1.4 m, and the dimension of the beam are h 254 mm, b- 143 mm, and t-1-51 mm. Determine the maximum transverse shear stress in the beam. Give your answer in MPa to 3 decimal places B 2IN NEZ
poru i Henuz cevaplanmadı 5,00 uzerinden işaretlenmiş y F Soruyu işaretle H The internal shear force V at a certain section of a beam is 49,9 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=99 mm, b=196 mm, c=10 mm and t=12,2 mm, Determine the location of the centroid of the cross-section in the y-axis from the bottom (mm). Yanıt:
H h V b The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the location of the centroid of the cross-section in the y-axis from the bottom (mm).
A pontoon bridge (see figure) is constructedof two longitudinal wood beams, known as balks,that span between adjacent pontoons and supportthe transverse floor beams, which are called chesses.For purposes of design, assume that a uniform floorload of 7.5 kPa acts over the chesses. (This loadincludes an allowance for the weights of the chessesand balks.) Also, assume that the chesses are 2.5 m long and that the balks are simply supported with aspan of 3.0 m. The allowable bending stress in thewood is 15 MPa.(a) If the balks have a square cross section, what istheir minimum required width bmin?(b) Repeat part (a) if the balk width is 1.5 b andthe balk depth is b; compare the cross-sectionalareas of the two designs.
The composite beam in Fig. a is made of wood and reinforced with a steel strap located on its bottom side. If the beam is subjected to a bending moment of M = 2 kN # m, determine the normal stress at points B and C. Take Ew = 12 GPa and Est = 200 GPa.
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
A horizontal beam of length 4 m and mass 9.0 kg has a mass of 3.0 kg and width 0.8 m sitting at the end of the beam (see the following figure). What is the torque due to gravity (in N m) on the beam-block system about the support at the wall? (Enter the magnitude.) Wall support 0.8 m, 3.0 kg 4 m, 9.0 kg N-m
From the given figure below, determine the flexural stress of the beam at fixed end if it has a cross section of 150mm wide by 250mm deep. HA VA 0 1750 40 N/m 3m -420Nm B & Im 550 35 N -75Nm с + 0° 55'N 20N 20N 0° DAV-DIAG -20Nm M-DIAG
The beam AB shown in the figure supportsa uniform load of intensity 3000 N/m acting over halfthe length of the beam. The beam rests on a foundationthat produces a uniformly distributed load overthe entire length.(a) Draw the shear-force and bending-momentdiagrams for this beam.(b) Repeat part (a) for the distributed load variationshown in Fig. b.
Since the bending safety stress σem = 10 MPa, shear safety stress τem = 600 kPa of the rectangular section beam given in the figure and whose width is b = 150 mm, the height of the beam section h is at least how much is the height of the beam section in order not to exceed the safety stress values. should be.