2. Technician A says that the purpose of the steering wheel holder is to make sure that the steering wheel is centered after the alignment. Technician B says that if the steering wheel is not centered after an alignment, it should be pulled off the column and positioned correctly. Who is correct? a. Technician A c. Both A and B b. Technician B d. Neither A nor B

Q: Which option limits rotation of the UCS to around the X axis?

A: The full form of UCS is the User Co-ordinate system. This is used in AUTO-CAD.

Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…

A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Tech A says that camber changes as the suspension moves up and down.  Tech B says that camber…

A: Camber angle : The angle made by the vertical axis with the wheel is known as camber angle . It is…

Q: Quiz 2- A slider "B" moves along a hinged rod, which is rotating coordinate system is best for…

A: Option B : Radial/ Transverse coordinates.

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: What results from having different axle ratios on thefront and rear of a 4WD vehicle when it is…

A: Given Data : 4WD Axle ratio

Q: Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type…

A: Solution:

Q: Explain the primary operational difference between a full time and a part time four wheel drive…

A: Introduction A four-wheel drive vehicle, often known as a 4WD or four-by-four, is one that receives…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: All of the following should be done post-repair EXCEPT: Select one: a. go back through the vehicle…

A: The option C is the step that is looked at during the initial phase, not at the time of delivery or…

Q: What can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear…

A: The correct option is d. clutch slipping. Excessive clutch pedal free play can cause the clutch to…

Q: The part (most likely to fail) in a parallelogram-type steering system is the ______.   a. idler…

A:

Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…

A: Technician A is correct.

Q: tart capacI 11. A cylindrical sleeve bearing, typically made of bronze, is called a A. bushing B.…

A: To find :- Correct option

Q: 55. The outside edge of the right front tire is worn, but the center and inside edges are almost…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: The steering wheel angle is 80° and the steering ratio is 14. Calculate the slip angle of each wheel…

A: Steering angle = 80oSteering ratio = 14The objective is to calculate the slip angle of each wheel in…

Q: When discussing axle hub nuts, Technician A says that they are never to be reused after they have…

A: Solution:

Q: When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may…

A: Solution:

Q: . Technician A says that leaf spring-type rear sus- pensions are subject to axle tramp. Technician B…

A: We are authorized to answer one question at a time since you have mentioned question 4 only so we…

Q: When adjusting a vehicle to counter the effect of road crown, what is the adjustment would you…

A: -Adjust the left front wheel with slightly less positive caster When adjusting a vehicle to counter…

Q: Explain the function of the following system and its use. Is there any difference between front and…

A: Explanation: 1) This is an example of hydraulic brake system.  2) This is used in light motor three…

Q: where are the wave springs or cushion springs located in a clutch disc? a. between the drive hub and…

A: The correct option is d. between the rear clutch facing and pressure plate. Wave springs, also known…

Q: Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid…

A: Hypoid gear is spiral bevel gear in which the axes doesn't intersect and it is not parallel.  This…

Q: A discussion concerning CV joint testing is being held. Technician A says that a recommended method…

A: CV Joint:  CV joint means Constant Velocity Joint. They are used to transfer the power in a variable…

Q: When reviewing the service procedures for CV joints and drive axles, Technician A says that the axle…

A: The axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle as…

Q: 1. Technician A says that the use of firmer, ure- thane bushings in the suspension improves the…

A: As per the Bartleby Answering guidelines we are supposed to answer first three questions. Please…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.