Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 48, Problem 10ASRQ
While diagnosing the cause of a constant SRS warning light: Technician A follows the service procedures and connects a jumper wire across designated pins in the DLC then records the flashed codes. Technician B connects a scan tool to the DLC and records the displayed codes. Who is correct?
- Technician A only
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that some types of voltage sensors provide input to the computer by modifying or controlling a constant, predetermined voltage signal. Technician B says that a coolant temperature sensor is a voltage-generating sensor. Who is correct?
Which of the following statements is not true?
a. DTCs that will not affect emissions will never illuminate the MIL.
b. An active or current DTC represents a fault that was detected and occurred during two trips.
c. When a two-trip fault is detected for the second time, a DTC is stored as a pending code.
d. There are some DTCs that will set in one trip
Check the correct statements. *
Attitude indicator must be adjusted during flight
ASi must be adjusted when aircraft changes altitude
Altimeter must be manually adjusted during flight
The pressure inside the aneroid is kept at sea level when it comes to the altimeter
Smaller aircraft normally use digital instruments
smaller aircraft normally have several pitot tubes and static ports
Chapter 48 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 48 - What is the difference between a passive and an...Ch. 48 - Prob. 2RQCh. 48 - Describe the three types of safing sensors.Ch. 48 - Prob. 4RQCh. 48 - True or False? The air bag diagnostic monitor...Ch. 48 - True or False? The powdery substance released from...Ch. 48 - True or False? When servicing the steering wheel...Ch. 48 - Which of the following statements about the SRS...Ch. 48 - Describe the two basic types of passenger weight...Ch. 48 - What type of scat belt operates automatically with...
Ch. 48 - Which of the following is false? The air bag...Ch. 48 - List at least five service precautions that must...Ch. 48 - Prob. 13RQCh. 48 - Which of the following statements about two-stage...Ch. 48 - Which of the following statements about seat belt...Ch. 48 - Prob. 1ASRQCh. 48 - Technician A says that seat belt webbing should be...Ch. 48 - Technician A says that the module assembly will...Ch. 48 - While testing seat belt retractors: Technician A...Ch. 48 - Technician A checks the clockspring electrical...Ch. 48 - Technician A removes the positive battery cable...Ch. 48 - Technician A says that ignition of the air bag...Ch. 48 - Technician A says that the steering column...Ch. 48 - While diagnosing a seat belt that will not buckle:...Ch. 48 - While diagnosing the cause of a constant SRS...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements about the SRS warning lamp is not true? When the ignition is first turned on, the indicator should turn on and remain on for approximately 6 seconds. If the system seems to be able to work correctly, the lamp will stay lit as the engine runs. If the lamp flashes or turns off and then turns on again, low source voltage may be indicated. A system problem is indicated when the lamp does not turn on when the ignition is initially turned on.arrow_forwardTrue or False? In a high-speed CAN system, a serial data bus is used to allow communication between the various control modules in a vehicle.arrow_forward
- While diagnosing an electronic control system: Technician A turns the ignition off before disconnecting a connector or component. Technician B uses a jumper wire to bypass a potentially faulty sensor and then observes the scan tool. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? In a high-speed CAN system, a serial data bus is used to allow communication between the various control modules in a vehicle.arrow_forwardWhen working on a high-voltage system, it is best to keep anyone who is not part of the service away from you and the car by creating a buffer zone around the car. Technician A makes sure the outside edges of the zone are at least one foot away from the car. Technician B places orange cones to define the outer boundaries of the zone. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which of the following lab scope controls must be set when trying to observe how long an event takes place? Intensity Vertical Horizontal Triggerarrow_forwardTrue or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forwardTrue or False? A bad ground can cause an increase in the reference voltage to a sensor.arrow_forward
- Technician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward9. Technician A says that navigational systems rely on global positioning satellites. Technician B says that navigational systems rely on information programmed in its memory and information stored on a CD or DVD. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License