Concept explainers
1 kg of oxygen is heated from 20 to 120°C. Determine the amount of heat transfer required when this is done during a (a) constant-volume process and (b) isobaric process.
FIGURE P4–62
The amount of heat transfers to constant-volume process.
The amount of heat transfers to isobaric process.
Answer to Problem 62P
The amount of heat transfers to constant-volume process is
The amount of heat transfers to isobaric process is
Explanation of Solution
Write the general expression for the energy balance equation.
Here, the total energy entering the system is
Simplify Equation (I) and write energy balance during a constant-volume process.
Here, the heat to be transfer into the system is
Take the oxygen as the system.
Substitute
Here, the mass of oxygen is
Rewrite the Equation (I) and write energy balance during a constant-pressure process.
Here, the heat to be transfer into the constant-pressure process is
Since, the quasi-equilibrium process during a constant pressure
Determine the change in temperature.
Here, the initial temperature oxygen is
Write the expression for linear interpolation method.
Here, the result of constant-pressure of specific heat is
Conclusion:
Substitute
Substitute
From above calculation the constant-pressure of specific heat is
Substitute
From above calculation the constant-volume of specific heat is
From the Table A-2b “Ideal-gas specific heats of various common gases”, obtain the value of constant-volume specific heat of air at 300 K temperature as
Substitute
Thus, the amount of heat transfers to constant-volume process is
Substitute
Thus, the amount of heat transfers to isobaric process is
Want to see more full solutions like this?
Chapter 4 Solutions
CONNECT FOR THERMODYNAMICS: AN ENGINEERI
- Water is contained in a cylinder/piston arrangement fitted with upper stops which limit the volume to 0.2 m maximum. The mass of the water is 0.26 kg, and the weight of the piston and the atmospheric pressure are balanced when the internal pressure is 200kPa. Initially, the piston pushes against the upper stops, and the pressure is 400 kPa. The water is allowed to slowly cool down to a temperature of 110°C. Sketch the process on both the P-v and the T-v diagrams. Label all relevant points and assignarrow_forwardTHERMOFLUID 100 grams of R-134a initially fill a weighted piston cylinder device at 60 kPa and -20°C. The device is then heated until the temperature is 100°C. Determine the change in the device's volume as a result of the heating.arrow_forwardA closed vertical cylinder containing 0.3 kg of nitrogen at 90°C is fitted with a weighted, frictionless piston so that a constant pressure of 275 kPa is maintained on the gas. The nitrogen is stirred by a paddle wheel inserted through the cylinder wall until the until the absolute temperature of gas is doubled. During the process 20 kJ of heat is transferred from the nitrogen to the sorroundings. Determine the amount of paddle-wheel work required for this process.arrow_forward
- A 752-cm sample of water was placed in a 1.00-kg aluminum pan. The inital temperature of the pan was 26°C and the final temperature of the system was 39°C. What was the initial temperature of the water?arrow_forward3-34 10 kg of R-134a fills a 1.115 m³ rigid container at an initial temperature of -30°C. The container is then heated until the pressure is 200 kPa. Determine the final temperature and the initial pressure.arrow_forwardSee Attachedarrow_forward
- See Attachedarrow_forwardSteam is contained in a 4-L volume at a pressure of 1.5 MPa and a temperature of 400 C. If the pressure is held constant by expanding the volume while 20 kJ of heat is added, the final temperature is nearestarrow_forwardA frictionless piston-cylinder device initially contains 200L of saturated liquid refrigerant-134a. The piston is free to move and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 70C. Calculate the work done during this process. ANS. 5571 KJA fixed mass of an ideal gas is heated from 50 to 80°C at a constant pressure of (a) 1 atm and (b) 3 atm. For which case do you think the energy required will be greater?arrow_forward
- A spring-loaded piston-cylinder device contains 100 g of helium as the system, as shown in the figure. The system undergoes a process from 115 kPa and 0.8739 m3 to 550 kPa and 0.3832 m³. Determine the (a) work done, (b) heat transfer in this process. The properties of helium are R= 2.08 kJ/kg-K and cy= 3.16 kJ/kg-K. Also, determine the (c) initial temperature and (d) final temperature of helium. - Spring Helium The work done in this process is The heat transfer in this process is| The initial temperature of helium is The final temperature of helium is kJ. kJ. °С. °C.arrow_forwardAn insulated container is partly filled with oil. The lid of the container is removed, 0.107 kg of water heated to 97.0°C is poured in, and the lid is replaced. As the water and the oil reach equilibrium, the volume of the oil increases by 1.40x10-5 m³. The density of the oil is 941 kg/m³, its specific heat capacity is 2250 J/(kg-C°), and its coefficient of volume expansion is 683x10-6 (Cº)-¹. What is the temperature when the oil and the water reach equilibrium? Number i Units °℃arrow_forwardA rigid tank of volume 0.6 m3 contains saturated R-134a vapor at 24°C. The contents are cooled until the temperature is O°c. How much heat is removed? Show the process on a P-v diagram.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY