Explanation Given information: The rods are made from A992 steel. The modulus of elasticity of the steel is E . The diameter of each rod is d . The force is applied to the rods ( P ) is 100 kip . The allowable normal stress of the steel ( σ allow ) is 24 ksi . The length of the rods ( L ) is 2 ft . Calculation: Show the free-body diagram of joint A as in Figure 1. Refer Figure 1. Here, F A B is force of the rod AB , F A C is force of the rod AC , and F A D is force of the rod AD . Calculate the horizontal forces by applying the equation of equilibrium: Sum of horizontal forces is equal to 0. ∑ F x = 0 ( F A B × sin 30 ° ) − ( F A C × sin 30 ° ) = 0 sin 30 ° ( F A B − F A B ) = 0 F A B − F A B = 0 F A B = F A B Therefore, F = F A B = F A B Calculate the vertical forces by applying the equation of equilibrium: Sum of vertical forces is equal to 0. ∑ F y = 0 2 F × cos 30 ° + F A D − 100 = 0 1.732 F + F A D = 100 (1) Show the geometry of the deformation diagram of the rodsas in Figure 2. Refer to Figure 2. Here, δ F A D is deformation due to F A D and δ F is deformation due to force. Due to symmetry, the joint A will displace vertically. Calculate the forces of the rods ( F and F A D ) using the deformation: δ F = δ F A D cos 30 ° F L A E = F A D ( L cos 30 ° ) A E × cos 30 ° F = F A D ( cos 30 ° ) 2 F = 0

9th Edition

ISBN: 9789810694364

Author: Russell C Hibbeler

Publisher: Pearson Education

See similar textbooks

Videos

Question

Chapter 4.5, Problem 4.63P

To determine

The required diameter to the nearest 18 in. of each rod (D) .

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4.5, Problem 4.62P

Chapter 4.5, Problem 4.64P

Students have asked these similar questions

A gearbox has permanent shaft positions defined by the bearing mounting positions, but the gear ratio can be changed by changing the number of teeth in the pinion and gear. To achieve similar power transmission ability for different gear ratios, a manufacturer chooses to have the same module for two different gearboxes. One of the gaerboxes has a pinion with 22 teeth, a gear with 68 teeth, and a center distance of 225mm. How large is the gear module and which gear ratios are possible for a pinion with 22 or more teeth using the same module?

A gear train has a 50.3 mm circular pitch and a 25 degree pressure angle and meshes with a pinion having 12 teeth Design this gear train to minimize its volume and the total number of teeth. Obtain the pitch diameters the number of teeth the speed ratio the center distance and the module of this gear train. The gearbox housing has a diameter of 620mm

Handwritten solution required ,strictly do not use CHATGPT. MECHANICAL ENGG

Chapter 4 Solutions

Mechanics Of Materials, Si Edition

Ch. 4.2 - In each case, determine the internal normal force...Ch. 4.2 - Determine the internal normal force between...Ch. 4.2 - The post weighs 8kN/m. Determine the internal...Ch. 4.2 - The rod is subjected to an external axial force of...Ch. 4.2 - The rigid beam supports the load of 60 kN....Ch. 4.2 - The 20-mm-diameter A-36 steel rod is subjected to...Ch. 4.2 - Segments AB and CD of the assembly are solid...Ch. 4.2 - The 30-mm-diameter A992 steel rod is subjected to...Ch. 4.2 - If the 20-mm-diameter rod is made of A-36 steel...Ch. 4.2 - The 20-mm-diameter 2014-T6 aluminum rod is...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The required diameter to the nearest 1 8 in . of each rod ( D ) .

Videos

The required diameter to the nearest 18 in. of each rod (D) .

Want to see the full answer?

Chapter 4 Solutions