Precision Machining Technology (MindTap Course List)
2nd Edition
ISBN: 9781285444543
Author: Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4.3, Problem 6RQ
What is spotting and why is it performed?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Tandem drawing of wires and tubes is
necessary because;
Surface finish improves after every
drawing stage
OIt is not possible to reduce at one stage
O Annealing is needed between stages
Accuracy in dimensions is not possible
otherwise
Which of the following abrasive
materials is most appropriate for
grinding nonferrous metals?
Silicon carbide
O Aluminum oxide
Cubic boron nitride
Diamond
Which is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?
What is a transfer-type measuring tool?
Chapter 4 Solutions
Precision Machining Technology (MindTap Course List)
Ch. 4.1 - Upright drill presses are available in _______ and...Ch. 4.1 - List two general types of upright drill press...Ch. 4.1 - Explain how the size of an upright drill press is...Ch. 4.1 - Briefly describe the term sensitive drill press.Ch. 4.1 - Briefly describe a gang drill press and its...Ch. 4.1 - When would a radial-arm drill press most likely be...Ch. 4.1 - Briefly describe a micro drill press and its...Ch. 4.2 - What are the two main materials used to make...Ch. 4.2 - What two types of shanks are commonly found on...Ch. 4.2 - Name three functions of the flutes on a twist...
Ch. 4.2 - Name two types of flute styles for machine...Ch. 4.2 - Prob. 5RQCh. 4.2 - What is the major difference between counterboring...Ch. 4.2 - What must be used to secure a workpiece to an...Ch. 4.2 - What devices are used to elevate a workpiece to...Ch. 4.2 - If 50 parts measuring 1" I" 3" each needed a...Ch. 4.2 - Which would be the best workholding device for...Ch. 4.2 - Which would be the best workholding device for...Ch. 4.2 - Which would be the best workholding device for...Ch. 4.3 - List five drill press safety guidelines.Ch. 4.3 - Briefly define the term cutting speed.Ch. 4.3 - What unit of measure is used to define cutting...Ch. 4.3 - What is feed, and how is feed stated for drill...Ch. 4.3 - Briefly describe two methods for locating hole...Ch. 4.3 - What is spotting and why is it performed?Ch. 4.3 - What is pecking, or peck drilling?Ch. 4.3 - Briefly contrast the speed and feed differences...Ch. 4.3 - What drill press component can be used to control...Ch. 4.3 - Calculate feed depth for a 90-degree countersink...Ch. 4.3 - Calculate feed depth for an 82-degree countersink...Ch. 4.3 - What benefit does tapping on the drill press offer...Ch. 4.3 - How many turns must a 1/4-20 tap be turned into a...Ch. 4.3 - Prob. 14RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- is the method of skewness used in ansysarrow_forwardWhat is a simple way of correcting slight alignment problems?arrow_forwardEstimate the manufacturing cost for a simple machined component: a. Compare the costs for manufacturing volumes of 1, 10, 100, 1000, and 10,000 pieces with an intermediate tolerance and surface finish. Explain why there is a great change between 1 and 10 and a small change between 1000 and 10,000 pieces. b. Compare the costs for fit, intermediate, and rough tolerances with a volume of 100 pieces. c. Compare the costs of manufacturing the component out of various materials.arrow_forward
- 8. A note in the comment section of a title block mentions that all faces should have a +.10 tolerance before heat treatment. The machinist follows the instructions but for diameters he leaves a tolerance of +.20. Why? O A. The machinist may have committed an error, and the part must be returned prior to heat treatment. OB. Diameter dimensions usually change by twice as much as the faces. OC. The tolerances for diameters aren't as critical as face tolerances. D. It's easier for the machinist to adopt MMC for diameters.arrow_forwardQuestion 1 1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2. Complete any missing information on part 1&2 and in feature control 1 &2 (assume any tolerance). Explain your analysis ..not just numbers. 3. Add all information needed for Gage 1 & 2 used to inspect Part 1&2 (show your calculations) Part 1 Part 2 Ø1.000+.000 -.005 Ø1.005+.005 -.000 Ø.500+.000 -.005 +.005 Ø.505000 OØ. Ø. Gage 1 Gage 2 7.arrow_forward-How many holes require drilling? -What is the center to center distance of the 6mm tapped holes? -What tap drill is used for holes marked Z? -How many surfaces are machine finished? -What are the dimensions of the face marked F & C? -What are the dimensions have symbols A, E &, B -In what dihedral angle is the drawing made? -What is the max and min dimensions of D -What is the tolerance of measurement D?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License