Traffic and Highway Engineering - With Mindtap
5th Edition
ISBN: 9781305360990
Author: Garber
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 4P
To determine
Whether the engineer has met with all of the requirements of the study
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
An engineer wishing to obtain the speed characteristics on a bypass around her city at
a confidence level of 95%, and an acceptable limit of 1.0 mi/h collected a total of
130 spot speed samples and determined that the variance is 25 (mi/h)2
. Has the engineer met with all of the requirements of the study?
An engineer wishing to obtain the speed characteristics on a bypass around her city at
a confidence level of 95%, and an acceptable limit of + 1.0 mi/h collected a total of
130 spot speed samples and determined that the variance is 25 (mi/h). Has the engi-
neer met with all of the requirements of the study?
Question 4
One stretch of two-lane two-way roadway that traverses through level terrain is expected
to carry 1400 vehicle per hour. Determine the Level of Service (LOS) in the peak
direction for the road based on average travel speed (ATS) if the characteristics of the
roadway are as follows:
Table Q4-1
Percentage of Trucks
Percentage of Recreational Vehicle
Peak Hour Factor
10
0.97
60:40
60
Percent Directional Split
Percent no-passing Zone
Lane Widths
Shoulder Widths
Design Speed
Road Length
Access Points
3.35 m
1.2 m
96 km/h
8 km
10 access points per km
State all assumption (if any) used in calculation..
Chapter 4 Solutions
Traffic and Highway Engineering - With Mindtap
Knowledge Booster
Similar questions
- Prove that it is safearrow_forwardQuestion 1 Calculate the stopping sight distance on a highway at a descending gradient of 3% for a design speed of 100 kmph. Assume other data as per IRC recommendations. Question 2 Calculate the safe stopping distance while travelling at a speed of 80 kmph on an upward gradient of 2 percent. Make suitable assumptions.arrow_forward5. Calculate the minimum passing sight distance required for a two-lane rural roadway that has a posted speed limit of 45 mi/h. The local traffic engineer conducted a speed study of the subject road and found the following: average speed of the passing vehicle was 47 mi/h with an average acceleration of 1.43 mi/h/sec, and the average speed of impeder vehicles was 40 mi/h.arrow_forward
- The following travel times were observed for 4 vehicles traveling a one km segment of the SLEX. It is required to determine the space mean speed of these vehiclesarrow_forwardA driver traveling down a 4% grade collides with a roadside object in rainy conditions, and is issued a ticket for driving too fast for conditions. The posted speed limit is 65 mi/h. The accident investigation team determined the following: The vehicle was traveling 40 mi/h when it struck the object, braking skid marks started 205 ft before the struck object, the pavement is in good condition, and the braking efficiency of the vehicle was 93%. Using theoretical stopping distance, assuming aerodynamic resistance is negligible, and with the coefficient rolling resistance approximated as 0.015, should the driver appeal the ticket? Why or why not?arrow_forwardTraffic engineering شنبنسarrow_forward
- Nonearrow_forwardCalculate the minimum passing sight distance required for a two-lane rural roadway that has a posted speed limit of 45 mi/h. The local traffic engineer conducted a speed study of the subject road and found the following: average speed of the passing vehicle was 47 mi/h with an average acceleration of 1.43 m/h/sec, and the average speed impeder vehicles was 40 mi/h.arrow_forwardb- It was required to estimate AADT for a rural highway (16) hours data were collected for Friday ,Saturday and Wednesday during June the traffic volume were as follow Friday (7000) vehs. Saturday (8000) vehs. Wednesday (10000) vehs. The percentage of June traffic (116%) of the average then find future directional design hourly volume let (16 hours = 93% of a day traffic, k=0.12,D=0.55, r=0.06, x=2, n=20)arrow_forward
- A highway has a posted speed limit of 50mph and, on one section, has both horizontal and vertical curves, as shown in the following Figure. A recent daytime crash (driver traveling and striking a stationary roadway object) resulted in a fatality and a lawsuit alleging that the speed limit is an unsafe speed for the curves. 1) Evaluate if the roadway design (horizontal and vertical curves) is reasonable as compared to the minimum curve length requirement due to sight distance. 2) Based on the above calculations, comment if the roadway design is the cause of this crash. Plane view PC=16+00 Profile view G1=-2% 24ft Sight obstruction 80⁰ PVC = 14+00 e= 8% PT=32+75 G2= + 4% PVT=18+80 Narrow_forwardData obtained from aerial photography showed six vehicles on a 600 ft – long section of road. Traffic data collected at the same time indicated an average time headway of 4 sec. Determine (a) the density on the highway, (b) the flow on the road, and (c) the space mean speed.arrow_forwardAn old 6-lane (3 lanes each direction) rural freeway segment has 11 ft lanes and frequent roadside obstructions located 10 ft from the right edge of the pavement. What is the estimated FFS (mph) for the 3 northbound lanes? Provide the answer to the nearest tenths. Response Feedback: The BFFS of 75.4 mph is adjusted by 1.9 mph for the 11 ft lanes.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning