1. During Atterberg limit tests in the soil mechanics laboratory, the students obtained the following results from a clayey soil. Liquid limit tests: Number of Moisture blows, N content (%) 14 38.4 16 36.5 20 33.1 28 270 Plastic limit tests: Students conducted two trials and found that PL = 172% for the first trial and PL = 17.8% for the second trial. a. Draw the flow curve and obtain the liquid limit. b. What is the plasticity index of the soil? Use an average value of PL from the two plastic limit trails.

1. During Atterberg limit tests in the soil mechanics laboratory, the students obtained the following results from a clayey soil. Liquid limit tests: Number of Moisture blows, N content (%) 14 38.4 16 36.5 20 33.1 28 270 Plastic limit tests: Students conducted two trials and found that PL = 172% for the first trial and PL = 17.8% for the second trial. a. Draw the flow curve and obtain the liquid limit. b. What is the plasticity index of the soil? Use an average value of PL from the two plastic limit trails.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A laboratory test was conducted according to Method A of the ASTM D4318 to find the liquid limit of…

A: The wet mass of the soil sample with the mass of the can is measured, again the dry mass of the…

Q: 1. A soil sample is collected at 20 °C and taken to the laboratory. The sample is in a stainless…

A: A soil sample in stainless steel cylinder is given with the weight of the cylinder and weight of…

Q: TABLE 2 RESULTS OF ORI TEST Water Content (%) Weight (Kg) 14 1.45 16.5 1.71 18.5 1.87 20 1.88 21…

Q: A glass cylinder 5 cm internal diameter with a screen at the bottom was used as a falling head…

Q: The results of a standard Proctor test are given in the following table. Given: Mold volume : 1/30…

Q: A Standard Proctor Test was completed according to Method A described in Chapter 12. The following…

Concept explainers

Laboratory Determination of Hydraulic Conductivity

Hydraulic conductivity is the measure of flowability of water inside the soil in the presence of a hydraulic gradient. The hydraulic gradient is defined as the difference in the water heads in the soil, which induces a water motion. In simple terms, a hydraulic gradient is the presence of a potential that induces a flow of water.

Question

1. During Atterberg limit tests in the soil mechanics laboratory, the students
obtained the following results from a clayey soil.
Liquid limit tests:
Number of
Moisture
blows, N
content (%)
14
38.4
16
36.5
20
33.1
28
270
Plastic limit tests: Students conducted two trials and found that PL = 172%
for the first trial and PL = 17.8% for the second trial.
a. Draw the flow curve and obtain the liquid limit.
b. What is the plasticity index of the soil? Use an average value of PL from
the two plastic limit trails.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Laboratory determination of hydraulic conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
Q1/ specimen of the fine-grained soil, 75 mm in diameter and 20 mm thick was tested in an oedometer in a laboratory. At applying pressure (240 kN/m²), the time with dial gauge readings are: Time (min) 0 Settlement (mm) 0 0.25 1 0.22 0.42 4 9 0.6 0.71 16 0.79 36 64 100 0.86 0.91 1.04 d 1- Find Coefficient of consolidation in cm²/s using root time and TV90% = 0.848. Scanned by TapScanner
Soil mechanics
A carefully-weighed 52.9 gram soil sample was dispersed for particle-size analysis using the Bouyoucos hydrometer method. The laboratory was held at a constant temperature of 20 C (68 F). The hydrometer reading after 40 seconds was 20.1 and the hydrometer reading after 8 hours was 5.1. What percentage of particles in the soil sample were clay-sized? Your Answer: Answer units
In a liquid limit test using Fall cone apparatus, the following readings were recorded. While in the plastic limit test, the following data were obtained: Weight of soil + container = 22.12 grams Weight of dry soil + container = 20.42 grams Weight of container = 13.07 grams Determine the ff. (SHOW COMPLETE SOLUTION AND GRAPH) A. Find the liquid limit B. Compute the plastic limit. C. Find the liquid limit. D. Find the plastic limit. 40% 45% 50% 58% Water Content 12 16 21 35 Penetration of cone(mm) -PLS SHOW COMPLETE SOLUTION AND GRAPH. SHOW YOUR ANSWER IN 4 DECIMAL PLACES. I'LL RATE, THANKS!
Hello can any one help me with this
Find the correct solution
The results of a Standard Proctor test are given in the following table. Moist Weight of Wet Sol Moisture Content in the mold (Ib) Trial (%) 26 4.08 28 4.12 30 4 4,18 32 Determine: 1. Maximum dry unit weight in Ib/ft^3 (4 decimal places) 2. Optimum water content in % (4 decimal places)
During Atterberg limit tessts in the Naboratory,the studens obtained the following results froma clayey soil. Wumber of Blows (N) Molsture Content \ 38/4 16 36/5 20 33.1 28 2/7 0 Plastic limit tests: Students conducted two trials and found that PL= 17 2% for the first trial and PL = 18.4% for the second trial. Assume that the liquid limit of the soil iS LL= 29.0% a. Determine the flow index. b. Determine the liquidity index of the soil if the in situ moisture content is 22.0%.
Tina 20 Two soil specimens with identical geometric dimensions were subjected to falling head permeability tests in the laboratory under identical conditions. The fall of water head was measured after an identical time interval. The ratio of initial to final water heads for the test involving the first specimen was 1.25. If the coefficient of permeability of the second specimen in 5 times that of the first, the ratio of initial to final water heads in the test involving the second specimen is
1.4 A test for the relative density of soil in place was performed by digging a small hole in the soil. The volume of the hole was 400 ml and the moist weight of the excavated soil was 9 N. after oven drying, the weight was 7.8 N. Of the dried soil, 4N was poured into a vessel in a very loose state, and its volume was found to be 270 ml. The same weight of soil when vibrated and compacted had a volume of 200 ml. Determine the relative density.
05: The Figure below represents the data that was obtained from a liquid-limit test on a soil. 50 percent of its particles is passing sieve #200. Two determinations for the plastic limit gave water contents of 20.3 % and 20.8 %. Determine 1- Liquid Limit (LL). 2- Plasticity index. 3- Liquidity index if the water content is 27.4% 4- Void ratio at the liquid limit, if G, 2.7 5- Classify the soil based on AASHTO system. 30 10 20 40 60 80 100 Penetration, d (mm) Moisture content, w ()