Engineering Fundamentals: An Introduction to Engineering
Engineering Fundamentals: An Introduction to Engineering
6th Edition
ISBN: 9780357112311
Author: Saeed Moaveni
Publisher: Cengage Learning US
bartleby

Videos

Question
Book Icon
Chapter 4, Problem 25P
To determine

Divide the example problem 8.3 in chapter 8 using the 4.2 section described in textbook into the format “Given” ,“Find” , and  “Solution”.

Expert Solution & Answer
Check Mark

Answer to Problem 25P

The example problem 8.3 in chapter 8 is divided using the 4.2 section described in textbook into the format “Given” ,“Find” , and  “Solution”, and the total distance travelled by the car is 50347.2m and the average speed of the car over its entire distance is 99.2kmh.

Explanation of Solution

Given:

Car accelerates at speed of 100kmh in 15 seconds from rest,

The car moves with constant speed of 100kmh for about 30 minutes,and

The car decelerates to a full stop in 10 seconds.

Find:

Find the total distance travelled by the car and also find its average speed over this distance.

Solution:

The car speed is linearly increased from zero to 100kmh for the first 15 seconds.

Therefore, the average speed of the car is 50kmh for this period.

Formula to determine the distance travelled during this period (t1) is,

d1=(time)(averagespeed)=(15s)(50kmh)(1h3600s)(1000m1km)      [1h=3600s,and1km=1000m]=208.3m

For the next 30 minutes (1800 s), the car travels with a constant speed of 100kmh.

Formula to determine the distance travelled during this period (t2) is,

d2=(time)(averagespeed)=(1800s)(100kmh)(1h3600s)(1000m1km)      [1h=3600s,and1km=1000m]=50000m

For the last 10 sec, the car decelerates at a constant speed of 100kmh to zero and attains a full stop of the car.

Therefore, the average speed of the car during the last 10 sec is also 50kmh for this period

Formula to determine the distance travelled during this period (t3) is,

d3=(time)(averagespeed)=(10s)(50kmh)(1h3600s)(1000m1km)      [1h=3600s,and1km=1000m]=138.9m

Formula to determine the total distance covered by the car is,

d=d1+d2+d3=208.3m+50000m+138.9m=50347.2m

Convert the unit of total distance from m to km

d=50347.2m=50.3472×103m=50.3472km

Formula to determine the average speed of the car for the entire duration of the travel is,

Vaverage=distancetravelledtime=50347.2m1825s=27.58ms

Convert the unit of average speed from ms to kmh.

Vaverage=(27.58ms)(3600s1h)(1km1000m)[1h=3600s,and1km=1000m]=99.2kmh

Conclusion:

Hence, the example problem 8.3 in chapter 8 is divided using the 4.2 section described in textbook into the format “Given” ,“Find” , and  “Solution”,

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
*13-12. The control linkage for a machine consists of two L2 steel rods BE and FG, each with a diameter of 1 in. If a device at G causes the end G to freeze up and become pin connected, determine the maximum horizontal force P that could be applied to the handle without causing either of the two rods to buckle. The members are pin connected at A, B, D, E, and F. P 12 in. C G F B 2 in. E 4 in. 4 in. A D + -15 in.- + -20 in.-
13-31. The steel bar AB has a rectangular cross section. If it is pin connected at its ends, determine the maximum allowable intensity w of the distributed load that can be applied to BC without causing bar AB to buckle. Use a factor of safety with respect to buckling of 1.5. Est = 200 GPa, σy 360 MPa. = B W 5 m 3 m -20 mm 30 mm x x A 20 mm y C
Problem 1: A man-made 30 ft tall, 1.5:1 slope is to be build as shown in the figure. The soil is homogeneous with shear strength parameters c = 400 psf and φ = 290 . The moist unit weight of the soil is 119 pcf above the groundwater table and the saturated unit weight is 123 pcf below. Using the ordinary method of slices, compute the Factor of Safety (FS) along the trial failure surface shown. (Hint: Please note the unit weight is changing within the same slice.) Note 1: Use the same number of slices and dimensions as provided. Document ALL the calculations of weight (W) for each slice. Note 2: Document your solutions by following the same approach illustrated in the class, including a summary table showing all the variables and calculations involved in assessing FS.
Knowledge Booster
Background pattern image
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
Text book image
Residential Construction Academy: House Wiring (M...
Civil Engineering
ISBN:9781285852225
Author:Gregory W Fletcher
Publisher:Cengage Learning
Introduction to Materials; Author: Industrial Heating;https://www.youtube.com/watch?v=R8EV8R8f5Tw;License: Standard Youtube License