Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
9th Edition
ISBN: 9781285180014
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 4, Problem 23RQ
What basic concept is used in a digital meter to calculate the circuit characteristics being measured?
- a. Watt’s law
- b. Volt’s law
- c. Amp’s law
- d. Ohm’s law
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
qq4
9. Which of the following is not an instrument used to measure flow by volume?
O Turbine flow meter
O Ultrasonic flow meter
O Thermal flow meter
All of these
Which of the following terms/ phrases describes the accuracy of measurement?
a
Depends on the instruments used
b
Standard deviation
c
Experimental error /Percent error
d
Reproducibility of a set of measurement
Chapter 4 Solutions
Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
Ch. 4 - What are the three most common electric meters...Ch. 4 - Prob. 2RQCh. 4 - What do most analog meters use to facilitate the...Ch. 4 - How does an ammeter work?Ch. 4 - What are the two types of ammeters? Which type is...Ch. 4 - Prob. 6RQCh. 4 - How can a very small ampere draw be measured with...Ch. 4 - If a conductor was wrapped around the jaws of a...Ch. 4 - Explain the operation of an analog voltmeter.Ch. 4 - Air-conditioning or refrigeration equipment can...
Ch. 4 - Prob. 11RQCh. 4 - What precaution should be taken when using an...Ch. 4 - Prob. 13RQCh. 4 - What is a short circuit?Ch. 4 - Prob. 15RQCh. 4 - What factors should be considered when purchasing...Ch. 4 - Match the following terms.Ch. 4 - Prob. 18RQCh. 4 - Prob. 19RQCh. 4 - An in-line ammeter must be connected to a circuit...Ch. 4 - What is the difference between an analog meter...Ch. 4 - Give three advantages of a digital electric meter.Ch. 4 - What basic concept is used in a digital meter to...Ch. 4 - What is the basic accuracy of most analog and...Ch. 4 - How many digits will the 312- and 412-digit...Ch. 4 - Prob. 26RQCh. 4 - The ohmmeter differs from other types of meters in...Ch. 4 - Compare the digital and analog types of electric...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False. In measurement there must be one-to-one correspondence between the numbers and the characteristics being measured. True Falsearrow_forwardA Profilometer is used to measure: How hard a part surface is. How round a part is to itself. The surface texture of a part. What the length of a part is.arrow_forwardif a measurement systems gives only a small spread of readings when repeated readings are taken of the same quantity, then what characteristics does the system have? a.High sensitivity b.High precision c.High repeatability d.High Producibilityarrow_forward
- MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .arrow_forwardwhats a multimeterarrow_forwardWhich statement is true in the case of the term "Precision". The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in condition of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in time of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in location. The closeness of output readings when the same input is applied repetitively over a short period of time and there is no change in observer.arrow_forward
- One of the major components of a residential electronic control circuit that measures temperature is a A. thermometer. B. thermistor. C. capacitor. D. filter.arrow_forwardWhat does "calibrating an instrument" mean?arrow_forwardThe sensitivity of a potentiometer depends on its actual supply voltage. True Falsearrow_forward
- Identify and discuss the function of each part: Hand Speed Tachometer Revolution Counter Tachoscope Centrifugal Force Tachometerarrow_forwardFrom the speed chart below, determine the correct cutting speed for facing an Aluminum part on a milling machine using a 1 in. diameter square-nose end-mill Surface Speed (Ft/Min) Aluminum Brass/Bronze Low Carbon Steel Cast Iron Alloy Steel 400 300 200 100 80 70 60 50 40 Diameter (in) N WAGO 10 0.8 0.4 0.3 0.2 0.1 Cutting Speed (RPM) I 10 20 30 40 50 60 70 80 100 200 300 400 500 600 700 800 1000 2000 3000 4000 5000 6000 7000 8000 10000arrow_forwardWhich statement is true in the case of the term "Range". The minimum and maximum values the instrument is designed to measure Is closely related to accuracy and output reading of an instrument is linearly proportional to the quantity being measured. Is not related to accuracy and define the maximum error of the measuring instrument during measurement process. Is closely related to accuracy and define the minimum and maximum values an instrument is designed to measure.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY