Explanation Given data: Refer to Figure given in the textbook. The current source is I g 1 = 12 A and I g 2 = 16 A . The resistors R 1 = 25 Ω , R 2 = 5 Ω , R 3 = 50 Ω , and R 4 = 75 Ω . Calculation: Refer to the equation given in the textbook, the sensitivity of the node voltage v 1 for the given circuit is as follows, v 1 = R 1 { R 3 R 4 I g 2 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] I g 1 } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (1) The sensitivity of v 1 with respect to I g 1 is calculated by differentiating equation (1) with respect to I g 1 as follows, d v 1 d I g 1 = R 1 { R 3 R 4 ( 0 ) − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( 1 ) } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 1 { 0 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 1 d I g 1 = − R 1 [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (2) The sensitivity of v 1 with respect to I g 2 is calculated by differentiating equation (1) with respect to I g 2 as follows, d v 1 d I g 2 = R 1 { R 3 R 4 ( 1 ) − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( 0 ) } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 1 = 0 , I g 2 = 1 } = R 1 [ R 3 R 4 − 0 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 1 d I g 2 = R 1 R 3 R 4 ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (3) Refer to the equation given in the textbook, the sensitivity of the node voltage v 2 for the given circuit is as follows, v 2 = R 3 R 4 [ ( R 1 + R 2 ) I g 2 − R 1 I g 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (4) The sensitivity of v 2 with respect to I g 1 is calculated by differentiating equation (4) with respect to I g 1 as follows, d v 2 d I g 1 = R 3 R 4 [ ( R 1 + R 2 ) ( 0 ) − R 1 ( 1 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 3 R 4 [ 0 − R 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 2 d I g 1 = − R 1 R 3 R 4 ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (5) The sensitivity of v 2 with respect to I g 2 is calculated by differentiating equation (4) with respect to I g 2 as follows, d v 2 d I g 2 = R 3 R 4 [ ( R 1 + R 2 ) ( 1 ) − R 1 ( 0 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 1 = 0 , I g 2 = 1 } = R 3 R 4 [ ( R 1 + R 2 ) − 0 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 2 d I g 2 = R 3 R 4 [ ( R 1 + R 2 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (6) Substitute 25 for R 1 , 5 for R 2 , 50 for R 3 , and 75 for R 4 in equation (2) to find the sensitivity of v 1 with respect to I g 1

ELECTRIC CIRCUITS-W/MASTERINGENGINEERING

11th Edition

ISBN: 9780134894300

Author: NILSSON

Publisher: PEARSON

See similar textbooks

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Mori…

Videos

Question

Chapter 4, Problem 107P

To determine

Find the values of node voltage v1 and v2 if Ig1 is decreased to 11 A and Ig2 is increased to 17 A of the given circuit using PSPICE.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 106P

Chapter 4, Problem 108P

Students have asked these similar questions

I need help in construct a method in matlab to find the voltage of VR1 to VR4, rhe current, and the power base on that circuit Nominal or Theortical: E1 = 3V , E2 = 9V, E3 = 1.5V R1 =10Kohm, R2 =2Kohm, R3 =1Kohm, R4 =16Kohm

Procedure:- 1- Connect the cct. shown in fig.(2). a ADDs Ds Fig.(2) 2-For resistive load, measure le output voltage by using oscilloscope; then sketch this wave. 3- Measure the average values f VL and IL: 4- Repeat steps 2 & 3 but for RL load. Report:- 1- Calculate the D.C. output vcl age theoretically and compare it with the test value. 2- Calculate the harmonic cont :nts of the load voltage, and explain how filter components may be selected. 3- Compare between the three-phase half & full-wave uncontrolled bridge rectifier. 4- Draw the waveform for the c:t. shown in fig.(2) but after replaced Di and D3 by thyristors with a = 30° and a2 = 90° 5- Draw the waveform for the cct. shown in fig.(2) but after replace the 6-diodes by 6- thyristor. 6- Discuss your results. Draw the waves on graph paper please Please solve No. 4 and 5

not use ai please chat gpt How to draw this in LtSpice

Chapter 4 Solutions

ELECTRIC CIRCUITS-W/MASTERINGENGINEERING

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Find the values of node voltage v 1 and v 2 if I g 1 is decreased to 11 A and I g 2 is increased to 17 A of the given circuit using PSPICE.

Concept explainers

Videos

Find the values of node voltage v1 and v2 if Ig1 is decreased to 11 A and Ig2 is increased to 17 A of the given circuit using PSPICE.

Want to see the full answer?

Chapter 4 Solutions