Explanation Given data: Refer to Figure given in the textbook. The current source is I g 1 = 12 A and I g 2 = 16 A . The resistors R 1 = 25 Ω , R 2 = 5 Ω , R 3 = 50 Ω , and R 4 = 75 Ω . Calculation: Refer to the equation given in the textbook, the sensitivity of the node voltage v 1 for the given circuit is as follows, v 1 = R 1 { R 3 R 4 I g 2 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] I g 1 } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (1) The sensitivity of v 1 with respect to I g 1 is calculated by differentiating equation (1) with respect to I g 1 as follows, d v 1 d I g 1 = R 1 { R 3 R 4 ( 0 ) − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( 1 ) } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 1 { 0 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 1 d I g 1 = − R 1 [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (2) From equation (4.46) in the textbook, the sensitivity of the node voltage v 2 for the given circuit is as follows, v 2 = R 3 R 4 [ ( R 1 + R 2 ) I g 2 − R 1 I g 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (3) The sensitivity of v 2 with respect to I g 1 is calculated by differentiating equation (2) with respect to I g 1 as follows, d v 2 d I g 1 = R 3 R 4 [ ( R 1 + R 2 ) ( 0 ) − R 1 ( 1 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 3 R 4 [ 0 − R 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 2 d I g 1 = − R 1 R 3 R 4 ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (4) Substitute 25 for R 1 , 5 for R 2 , 50 for R 3 , and 75 for R 4 in equation (2) to find the sensitivity of v 1 with respect to I g 1

10th Edition

ISBN: 8220100801792

Author: Riedel

Publisher: YUZU

See similar textbooks

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Mori…

Videos

Question

Chapter 4, Problem 105P

To determine

Find the values of node voltage v1 and v2 if Ig1 is reduced to 11 A of the given circuit using PSPICE.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 104P

Chapter 4, Problem 106P

Students have asked these similar questions

Q1. The three-phase full-wave converter in Figure shown is operated from a three phase Y-connected supply. Sketch the output voltages appeared at the load for firing angle 15°. I need Sketch an Ven จ T1 Q Yi₁ = I₂ a ia = is T₁ T3 T₂ Vbn b ib Load Highly inductive load ▲ T6 T₂ iT4 On T5, T6 T6, T₁ T2, T3 T3, T4 T4, T5 T5, T6 ཅ 0 T₁ الاسم T₁ Is wt

Q4. For the control system is shown in Figure 2, by using second method of Ziegler- Nichols, calculate the PID, PI-D and I-PD parameters and make tuning for this parameters to get accepting response for the هندسة الكم following system, then compare your results for all types controllers? R(S) K C(s) S3+4S² +11S Figure (2)

Q1. Consider the unity feedback control system whose open-loop transfer function is: G(s): = 40(S+2) s(s+3)(s+1)(s + 10) ELECTRIC Ziegler-Nichols, By using second method of Ziegler- Nichols, calculate the PID, PI-D and I-PD parameters and make tuning for this parameters to get accepting response for the following system, then comp controllers? PARTME then compare your results for all types GINEARI

Chapter 4 Solutions

EBK ELECTRIC CIRCUITS

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Find the values of node voltage v 1 and v 2 if I g 1 is reduced to 11 A of the given circuit using PSPICE.

Concept explainers

Videos

Find the values of node voltage v1 and v2 if Ig1 is reduced to 11 A of the given circuit using PSPICE.

Want to see the full answer?

Chapter 4 Solutions