Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 1RQ
Why are NEMA symbols such as push buttons, float switches, or limit switches not used in programmable logic controller schematics?
Expert Solution & Answer
To determine
Identify why the NEMA symbols for components such as push buttons, limit switches and float switches are not used in the schematic of a programmable controller.
Explanation of Solution
The programmable logic controller can only recognise whether a contact is open or closed. It doesn’t know if the contact is connected to components such as float switches, push buttons and so on.
Thus, there is no NEMA symbol used to identify components such as push buttons, limit switches and float switches in the schematic of a programmable controller.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
I want you to draw a ladder logic diagram of a garage door to control it by PLC. In my case we have different inputs and outputs and all of them gotta be used in the diagram. I can perfectly interpret the diagram so no need to explain it, I will just require you to draw it.
INPUTS : open push button ( OPB ) - close push button ( CPB ) - open limit switch ( OLS ) - close limit switch ( CLS ) - obstacle detection sensor ( ODS ) - safety sensor ( SS ) - emergency stop push button ( ESPB ) - reset button ( RB )
OUTPUTS : motor starts ( MS ) - motor stops ( MSTP ) - motor forward ( MF ) - motor reverse ( MR ) - Error display ( ER )
OPERATİNG MODES : automatic mode ( AM ) - manual mode ( MM )
NECESSARY TIMERS : T1 ( delay door movement after obstacle detection ) - T2 ( delay door movement after reversing )
Here is my excercise for today. Please I am requiring a good logic diagram taking into consideration all what was mentioned before.
so to sum up, I want you to write a logic ladder diagram…
Please draw a ladder diagram (plc) for this question
Design a PID controller for this system.
Chapter 39 Solutions
Understanding Motor Controls
Ch. 39 - Why are NEMA symbols such as push buttons, float...Ch. 39 - Prob. 2RQCh. 39 - Why are normally closed components such as STOP...Ch. 39 - Prob. 4RQCh. 39 - Prob. 5RQCh. 39 - List four basic rules for developing a program for...Ch. 39 - A PLC requires that times be programmed in...Ch. 39 - When programming in Boolean, what statement should...Ch. 39 - When programming in Boolean, what statement should...Ch. 39 - In a control circuit, it is imperative that a coil...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Name the four basic sections of a programmable logic controller.arrow_forwardTraffic Light System Construct a PLC program for a traffic light system with the following condition: The green light will be ON for 10 second, followed by the yellow light for 3 second and red light for 20. The system will run continuously until the START/STOP switch is deactivated. Figure 12: The traffic light system Two Directional Control of Traffic Light Extend the PLC program for the traffic light system with the following condition:. Red = north/south Green = north/south Amber = north/south Green = east/west Amber = east/west Red = east/west -25 s ·5 s 25 s 5 sarrow_forward10arrow_forward
- 1. A mixing vat has an inlet valve, an outlet valve, a mixing motor, and a single level detecting switch (Figure 1). Both valves are opened by solenoids. The level switch closes when the vat is full and stays closed until the vat is empty. Draw a PLC ladder logic diagram and provide the allocation list to do the following: a. When the start button is pushed, the inlet valve opens until the vat is full. b. The mixer motor comes on for 5 min. c. The outlet valve opens until the vat is empty. (closed) Level switch Motor Inlet valve Outlet valve Float Vat Figure 1arrow_forwardSápport Supp Suppórt Support 5 Types of External Connections (Pin, Ball in Socket (3D pin), Fix, Roller/Rocker, Sliding Support, Bearing) Question: Choose the type of External Connections for each image above and explain why?arrow_forwardName Section 5-2: Line Diagrams-Signals, Decisions, and Actions In the following application, a temperature switch controls a heating contactor and a flow switch is used to ensure there is enough air flow. If there is not enough air flow, an alarm is sounded. Complete the required information. 1. List all the signal devices in the circuit. 2. List all the action devices in the circuit. 3. List the decision part of the circuit that automatically sounds the alarm if there is a problem. 4. When the heating element is on during normal operation, is the flow switch open or closed? CIRCULATING 2 L1 FAN TEMPERATURE SWITCH TR HEATING ELEMENTS FLOW SWITCH -HOT AIR PADDLE AIR FILTER NORMALLY CLOSED FLOW SWITCH 65 ALARM (SOUNDS IF NO FLOW FOR 15 SECONDS OR MORE) Date HEATING CONTACTOR TR ON-DELAY TIMER SUPPLY AIR COLD AIR (3) TIME SET= 15 SEC © 2014 American Technical Publishers, Inc. All rights reservedarrow_forward
- What is an interrupt? define and explain how Transfer of Control via Interrupts?arrow_forwardMeans that data concerning the effects of the computers commands are fed back to the computer as an input signal.arrow_forwardDefine the following examples as path, motion, or function generation cases:arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License