Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 38, Problem 6RQ
When insulation on the inside of the duct comes loose it causes
A. the system to shut off.
B. high head pressure.
C. increased airflow.
D. reduced airflow.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What kind of circuit balancing valve is used in the hot and chilled water piping?
a. balancing globe valve
b. shut-off balancing valve
c. pressure balancing valve
d. pressure by-pass valve
Speed of the actuator is affected by
a.
pipe diameter
b.
all of the mentioned
c.
cross-section area of the orifice
d.
velocity of flow
True or false
The flexible duct system provides the lowest air resistance.
Chapter 38 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 38 - The three crafts normally associated with an...Ch. 38 - True or False: The flexible duct system is the...Ch. 38 - Name the two fasteners that typically fasten...Ch. 38 - What fastener is normally used to fasten round...Ch. 38 - True or False: Insulation on duct does not prevent...Ch. 38 - When insulation on the inside of the duct comes...Ch. 38 - Most duct insulation is made of_________.Ch. 38 - What is the purpose of the flexible duct...Ch. 38 - What happens if flexible duct is turned too...Ch. 38 - Why must flexible duct be stretched slightly for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass brush. C. using a chisel and hammer. D. running a mixture of sand and water through them.arrow_forwardWhat can be done to get water out from under the oil level in a compressor?arrow_forwardPressure relief valves: Select one: a. Open manually upon overloading in pressure O b. Open automatically upon overloading in pressure c. Two directional valve d. Oil flow control valvearrow_forward
- 17. Which of the following relief valves is designed to vent refrigerant under excessive pressure and then close when the system pressure has been lowered? A. Fusible plug. B. Manifold valve. ytor C. Rupture disc. D. Spring-loaded relief valve. e quicaarrow_forwardA one-way valve that lets air into the reservoir of a compressor, but does not let it out, is a Select one: O a. Receiver valve O b. Control valve O . Check valve O d. Three-way valvearrow_forwardIn cooling tower the blow down loss means a. the total water loss due to blowing of very fast air in cooling tower. b. the water loss due to leakges c. the water loss in the form of droplets d. the water loss to control impurities and saltsarrow_forward
- When there is an excess potential energy during the fluid flow, it can be stored using O a. pressure relief valve. O b. pressure reducing valve. O C. accumulator. O d. pressure absorbing valve.arrow_forwardThe process of filling the liquid into the suction pipe and pump casing upto the level of delivery valve is called as _________. a. leveling b. pumping c. priming d. fillingarrow_forwardWhat would happen if a hydronic system was installed without an expansion tank? A. The relief valve would open B. The system may flood constantly C. There would be no room for heated water to expand D. All the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License