Electric Motor Control
10th Edition
ISBN: 9781305177611
Author: Herman
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 38, Problem 4SQ
Why are capacitors connected into the power circuit?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
6
Multiple Choice 10 points
Use the measured characteristics given in the figure. From the curves shown, this is
220V Start
160V Start
190V Start,
DC series motor
DC shunt motor
DC separately excited motor
DC series generator
160V Start
220V Start
190V Start
000
.
Use the measured characteristics given in the figure. For Delta connected motor, the maximum load (N.m) you can put at starting is
"
28
"
24
22
28
24
18
14
13
3.4
2.8
3.6
0.9
1800
Can I have a written solution
Chapter 38 Solutions
Electric Motor Control
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 100-kVA, 2500/125-V, 50-Hz, step-down transformer has the following parameters: R1= 1.5Ω, X1= 2.8Ω, R2= 15mΩ, X2=20mΩ, Rc1= 3kΩ, Xm1= 5kΩ The transformer delivers 85% of the rated load at a terminal voltage of 115 V and a power factor of 0.866 lagging. Determine (a) the efficiency, and (b) the voltage regulation. Draw the phasor diagram of the transformer. Use the approximate equivalent circuit referred to the secondary side.arrow_forwardDon't use ai to answer I will report you answerarrow_forwardDon't use ai to answer I will report you answer.arrow_forward
- PV station 8.6 Consider the microgrid given in Figure 8.56. The positive sequence impedance of the transmission lines is given in the one-line diagram (Figure 8.56). The system data are as follows: PV generating station: 2 MW, 460 V AC; positive, negative, and zero sequence impedance of each line is equal to 10%. The gas turbine gen- erating station is rated at 10 MVA, 3.2 kV, with positive sequence reac- tance of 10%. The generator negative sequence impedance is equal to the positive sequence, and the zero sequence impedance is equal to half (1/2) of the positive sequence impedance. Transformers' positive sequence impedance is equal to the negative sequence and equal to the zero sequence impedance. DC/AC 3 CB T₁ AC PV bus YA 6 1+/10 20 CB CB CB m 0.5+15 личи 5 A S5 2 Gas turbine 0.3+16 7 ww NA Local S6 ST utility Figure 8.56 A one-line diagram for Problem 8.6.arrow_forwardCan you calculate the needed values. When it ask me to measure the values do I attach the function generator and use the values mentioned below? or do i leave the function generator off and measure? Any tips on how to connect the multimeters would be appreciated but not primary request.arrow_forwardDon't use ai to answer I will report you answerarrow_forward
- Don't use ai to answer I will report you answerarrow_forwardYou are tasked with designing an electronic system for sensing the magnitude of a measurand (details and values to be provided on the day of the exam). The system must alert a user to a measurand value above a threshold, measured by an appropriate sensor, by turning on a buzzer (to make a sound). The buzzer must remain off below this threshold. All resistors used must be from the E12 series. This work is to be performed on TinkerCAD. To fully answer the question, you must provide: • Full calculations for all components you use, clearly indicated what you are calculating. • A screenshot of the TinkerCAD circuit with it in the buzzer off state (clearly showing the full circuit including the sensor). • A screenshot of the TinkerCAD circuit with it in the buzzer on state (clearly showing the full circuit including the sensor). • A written explanation of how the circuit works and justification of your design (approx. 200 words).arrow_forwardcan I have a written solutionarrow_forward
- Q1 Q2 A control system is described by the block diagram in Figure 1 where R(s) is reference input and Y(s) is system output. (a) Find the transfer function Y(s)/R(s) using block diagram reduction. (b) Determine the steady state output in response to the unit step input. R(s) + + S 5 -~ $2 1 Y(s) 2s s² +2 Figure 1 A PID controller is designed to control the robot leg, and the control system is shown in Figure 2 where K is a positive gain. (a) Find the closed-loop transfer function (s)/R(s). (b) Use the Routh-Hurwitz stability criterion to determine the range of the parameter K such that the closed-loop system is stable. (s) 2 K 1+-+s s² + 3s+2 S R(s) PID Controller Robot Leg dynamics Figure 2arrow_forwardQ3 (a) For the digital control system given in Figure 3, by adding phantom samplers to show that the z transfer function of the closed-loop system is given by C(z) R(z) G(z) 1+ G(z) H₁H₂(z) + R(s) G(s) C(s) H₂(s) H₁(s) Figure 3 (b) The analogue compensator 5s + 1 D(s) = 0.4s +1 is implemented digitally with sampling period 0.2 seconds to control the depth of a submarine system. Use the pole-zero mapping method to find a digital approximation to the analogue compensator.arrow_forwardConsider an RC circuit with a 5 ohm resistor, a 0.05 faraday capacitor, and a constant 60 V battery. If the initial charge on the capacitor is zero, i.e. q(0) = 0 determines the charge on the capacitor at any time q(t).Strictly not using chatgpt or AI need proper explaination by handarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
02 - Sinusoidal AC Voltage Sources in Circuits, Part 1; Author: Math and Science;https://www.youtube.com/watch?v=8zMiIHVMfaw;License: Standard Youtube License