Torsional coil springs in the clutch disc __.a. cushion the driven disc engagement rear to frontb. are the mechanical force holding the pressureplate against the driven disc and flywheelc. absorb the torque forcesd. are located between the friction rings

Q: Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

A: Camshaft Camshaft is the shaft at which many cams are connected and it operates with the crankshaft.…

Q: The primary unbalanced force is maximum, when the crank position is

A: (a) The value of the primary force is maximum when the crank is perpendicular to the line of stroke.…

Q: Explain the importance of a cone clutch with an application

A:

Q: 4. Describe an application of a rotating cylinder. 5. What is a rod wiper? How is it installed? What…

A: A rotating cylinder can have many different applications depending on the specific design and…

Q: The pinion shaft is fitted with FAG inch-dimensioned tapered roller bearings mounted in O…

A: Factor of safety is a important aspect in making the structures especially for materials which are…

Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…

A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…

Q: What is used in a typical 4WD pickup truck to prevent driveline windup during turns?a. Constant…

A: Constant velocity joints in the driveshafts of a typical 4WD pickup truck are used to allow for…

Q: Compare three different types of clutches: single plate, conical friction and centrifugal, stating…

A: To Find:Compare the single plate, conical friction, and centrifugal clutch.Advantages of each…

Q: Derive the tension ratio of the belt drive.

A: let T1=tension in belt on tight sideT2=Tension in belt on slack sideθ=angle of contact in…

Q: A single disc clutch with both sides of the disc effective has outside diameter of 250 mm and inside…

A: A Clutch is a mechanical device used in the transmission system. clutch could be a machine…

Q: Identify the state under which the balls of a deep groove ball bearing cannot be changed. a.…

A: the balls of a deep groove ball bearing cannot be changed.

Q: The cars like Padmini and ambassador have axleless transmission in the front wheels explain how the…

A: The car like Padmini and ambassador have 5 speed manual with an overdrive transmission system. The…

Q: What is the rated flywheel power for a CAT 834H four-wheel tractor equipped with a converter drive?…

A: According to the given question  Rated power of the tractor = 523 HP Efficiency of the tractor = 92%…

Q: The axle of a front wheel of a bicycle shall belong to_____. A.Rotating shaft B. Drive shaft…

A: I think its answer should be part C- mandrel.

Q: aber of teeth for involute

A:

Q: A propeller shaft C having a diameter of 75 mm is mounted on two bearings B1 and B2 and is driven by…

A: Helical gear In helical gear the teeth of helical gears are cut in the form of a helix on the pitch…

Q: The axial load, mean radius, coefficient of friction, number of friction pairs are used to find the…

A:

Q: a 1 3/4 inch diameter shaft supported by two sleeve bearings, the total load on the two bearings is…

A: Given Data

Q: which among the following

A: Given: For an Oldham's coupling used between two shafts,Which statements are correct given in…

Q: Units 5 & 6: Closed Gear Systems Essay Questions Multiple-Choice Question Cog C. Rack D.…

A: (a) To find: The tooth profile of spur gear. Explain: The industrial equipment used to transfer…

Q: These are Considerations in Designing a Friction Clutch. Can you explain these conditions? The…

A:

Q: The output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A…

A: Given that the output shaft of a reducer has bearings A and B. The bearings are deep groove ball…

Q: A vehicle engine is producing a brake power of 56 kW with a torque of 132.2 Nm. The final drive…

A:

Q: 55. The outside edge of the right front tire is worn, but the center and inside edges are almost…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: the torque required to prod

A:

Q: is the wheel provided with a series of backward curved vanes. Select one: O a. Spiral casing O b.…

A: The centrifugal pumps are made up of many components like the suction pipe, delivery pipe, casing,…

Q: 1- Compare the theoretical value and practical value of the moment of inertia for flywheel? 2-…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: QUESTION 3 In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner…

A:

Q: An A-3 polyamde conveyor belt is to be.dnuen 530mm: Ihe pully shoift which is ya pulley with a…

A:

Q: Prove that the extreme values of the transmission angle occur when the crank is perpendicular to the…

A: Show the crank angle and transmission angle for slider crank linkage in figure(1) as below

Q: A significant disadvantage of using a flywheel with a reduced moment of inertia would most likely…

A: Given:   To select the correct option for the disadvantage of using a flywheel with less moment of…

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: where are the wave springs or cushion springs located in a clutch disc? a. between the drive hub and…

A: The correct option is d. between the rear clutch facing and pressure plate. Wave springs, also known…

Q: Essay Questions Multiple-Choice Questions Two or more gears working in tandem are called what? A.…

A: Ans.1: Option D is correct. Transmission Two or more gears working in tandem is called the…

Q: 2.5" 30.375" s 18.75" 4.25 26" 2.5" Espring FBY Fax 7 Analyze the forces acting on the clutch fork…

A: The force analysis can be done by using the equilibrium equation on anybody. The Shaft has lots of…

Q: What are various types of brakes?

A: Given The type of brake

Q: In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner diameter of…

A: Given data Outside diameter of clutch plate, do=15 inInside diameter of clutch plate, di=5…

Q: i need the answer quickly

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.