Why are carbon dioxide emissions a concern?

The concern for reasons behind emissions of carbon dioxide.
Explanation of Solution
The most basic and common element of life on earth is carbon. A colorless gas having density sixty percent higher than dry air generated upon burning of fuels. Human bodies are made up of carbon including the air we breath and crops we grow. The air we breathe, carbon present is used by plants for the process of photosynthesis.
Carbon dioxide is formed from the burning of fossil fuels. Carbon dioxide emission has caused greenhouse effect one of the serious problems in polluting the environment. It absorbs the heat from atmosphere and making the earth surface warmer. This has increased the average temperature by fifty-nine-degree Fahrenheit. Emission of carbon dioxide is released into atmosphere when any fossil fuel containing carbon is burnt. Plants absorbs carbon dioxide to build their and thus bringing level of carbon dioxide from atmosphere.
So, emission of carbon dioxide is really a concern as it is the major cause greenhouse effect.
Due to emission of carbon dioxide the water of oceans is becoming more acidic. Thus, affecting the life of water animals. Global warming is result of excess amount of carbon dioxide. It has alone contributed sixty-six percent in global warming. Excessive emission of carbon dioxide has brought following changes in atmosphere:
- It has increased the level of seas, people living in coastal areas life has be endangered.
- The supply of water has shrunken as the demand is increasing.
- It has brought some geographical changes.
- It has increased the severe weather conditions. Storms are becoming more frequent.
- It has affected the food supply change also.
Want to see more full solutions like this?
Chapter 36 Solutions
AUTOMOTIVE TECHNOLOGY (W/MINDTAP)
- Design and assemble on the fluidsim (or a draft) the Hydraulic Drive Circuit, with the following characteristics: (a) Sequential operation, pressure, for the advance and return of the cylinders (according to the proper operation for the device) controlled by a directional 4x3 way, closed center; (b) Speed control for the cylinders, according to the load signal; (c) Pressure counterbalance for cylinder A, in order to compensate for the weight of the assembly.arrow_forwardThis is an old exam practice question. The answer is Pmax = 218.8 kN normal stress governs but why?arrow_forwardMoist air initially at T₁ = 140°C, p₁ = 4 bar, and p₁ = 50% is contained in a 2.0-m³ closed, rigid tank. The tank contents are cooled to T₂ 35°C. Step 1 Determine the temperature at which condensation begins, in °C.arrow_forward
- Air at T₁ = 24°C, p₁ = 1 bar, 50% relative humidity enters an insulated chamber operating at steady state with a mass flow rate of 3 kg/min and mixes with a saturated moist air stream entering at T2=7°C, p₂ = 1 bar. A single mixed stream exits at T3-17°C, p3=1 bar. Neglect kinetic and potential energy effectsarrow_forwardHand calculation of cooling loadarrow_forwardAn HEV has a 24kW battery. How many miles can it go on electricity alone at 40 mph on a flat straight road with no headwind? Assume the rolling resistance factor is 0.018 and the Coefficient of Drag (aerodynamic) is 0.29 the frontal area is 2.25m^2 and the vehicle weighs 1618 kg.arrow_forward
- As shown in the figure below, moist air at T₁ = 36°C, 1 bar, and 35% relative humidity enters a heat exchanger operating at steady state with a volumetric flow rate of 10 m³/min and is cooled at constant pressure to 22°C. Ignoring kinetic and potential energy effects, determine: (a) the dew point temperature at the inlet, in °C. (b) the mass flow rate of moist air at the exit, in kg/min. (c) the relative humidity at the exit. (d) the rate of heat transfer from the moist air stream, in kW. (AV)1, T1 P₁ = 1 bar 11 = 35% 120 T₂=22°C P2 = 1 bararrow_forwardThe inside temperature of a wall in a dwelling is 19°C. If the air in the room is at 21°C, what is the maximum relative humidity, in percent, the air can have before condensation occurs on the wall?arrow_forwardThe inside temperature of a wall in a dwelling is 19°C. If the air in the room is at 21°C, what is the maximum relative humidity, in percent, the air can have before condensation occurs on the wall?arrow_forward
- ###arrow_forwardFind the closed loop transfer function and then plot the step response for diFerentvalues of K in MATLAB. Show step response plot for different values of K. Auto Controls Show solution for transform function and provide matlab code (use k(i) for for loop NO COPIED SOLUTIONSarrow_forwardThis is an old practice exam. The answer is Ta-a = 4.615 MPa max = 14.20 MPa Su = 31.24 MPa Sus = 10.15 MPa but why?arrow_forward
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning


