Electric Motor Control
10th Edition
ISBN: 9781305177611
Author: Herman
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 36, Problem 10SQ
To determine
Explain the reason to use the push buttons to restart a motor when the limit switches are used in Figure 36-2.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is the answer for Question 13?
Choice the correct answer
Which one of the following is not a part of an
induction motor?
a. Starter
b. Rotor
c. Stator
d. Terminal Box
e. Frame/Yoke
f. Bearing
g. Shaft
Chapter 36 Solutions
Electric Motor Control
Ch. 36 - Are the secondary resistors connected in three...Ch. 36 - Do secondary resistors on starters with three or...Ch. 36 - Does reversing the secondary rotor leads mean that...Ch. 36 - If one of the secondary resistor contacts (S2)...Ch. 36 - In Figure 362, how many different interlocking...Ch. 36 - Referring to Figure 364, why is it not possible to...Ch. 36 - Prob. 7SQCh. 36 - If there is a locked rotor in the secondary...Ch. 36 - Why is it necessary to remove the jumpers in...Ch. 36 - Prob. 10SQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How to avoid the effect of the high current at starting of the Motor? a. variable resistor is connected in series with Armature circuit b. variable resistor is connected in parallel with Armature circuit c. variable resistor is connected in series with field circuit d. None of the above Clear my choicearrow_forwardExplain how does the current will be reduced during the starting of the motor.arrow_forward6.a. When you're taking a PM motor apart you should exercise special care not to damage theA. end bells.B. commutator.C. permanent magnets.D. brush holders.6.b. A PM field servo motor may be equipped with a resolver that is used toA. excite the armature windings.B. create a voltage that increases with velocity.C. prevent the brushes from sparking.D. feed back position information.arrow_forward
- c) Based on Figure 3 (c), a basic DOL starter induction motor at a power station is experiencing run-time error and unable to start, based on your understanding, interpret the sequence of troubleshooting shall be carried out to identify the root cause of the abnormalities. 3P 1P MCB MCB STOP K1 START MOTOR Figure 3 (c)arrow_forward5. Which part (s) of the DC motor connect the power supply to the split- ring and coil? * O a) Carbon brushes O b) Magnets O c) Commutator d) Slip ringsarrow_forwardDraw an electrical diagram for a Star Delta starter with a forward rotation and reverse rotation switch.arrow_forward
- 1. Explain the working Principle of Single Phase Induction Motor. 2. What are the different types of Starters to control AC-Motor. Explain briefly. 3. Explain DOL starter of Single Phase Induction Motor briefly. 4. What is the purpose of the magnetic contactor? 5. What is the use of auxiliary contact in the magnetic controller? 6. What happens when the holding coil gets the supply in the magnetic controller? 7. Explain the working principle of a relay.arrow_forwardCan you please explain in details so I can understand even better. Topic: Electrical Machinesarrow_forwardWhen a d-c motor is tested by the electrical input method, the field rheostat is adjusted to giveA. rated speed at full load.B. rated speed at no load.C. maximum speed at minimum load.D. minimum speed at maximum load. Note: I have doubts if it is the letter A or the letter B, can you help me in this question, thanks.arrow_forward
- List the probable causes if the armature dos notable release after the magnetic starter is de - energized .arrow_forwardQ3/ Chose the correct answer for the following 1. Synchronous motors are generally not self-starting because (a) the direction of rotation is not fixed (b) the direction of instantaneous torque reverses after half cycle (c) startes cannot be used on these machines (d) starting winding is not provided on the machines 2. The power developed by a synchronous motor will be maximum when the load angle is (a) Zero (b) 45° (c) 90° (d) 120° 3. An over-excited synchronous motor takes (a) leading current (b) lagging current (c) both (a) and (b) (d) none of the above 4. In a synchronous motor, the magnitude of stator back e.m.f. £& depends on (a) d.c. excitation only (b) speed of the motor (c) load on the motor (d) both the speed and rotor flux 5. A pony motor is basically a (a) small induction motor (c) D.C. shunt motor (b) D.C. series motor (d) double winding A.C./D.C. motorarrow_forwardCan I use the Manual Motor Starter on a single phase motor? Why?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning