(a) Explanation Calculation: The length of beam is 4 m . Let the force and moment of couple acting in upward direction and moment of couple in anticlockwise direction are taken as positive and downward force and moment of couple in clockwise direction are taken as negative quantities. Write the expression to calculate the force part of force couple system. R = ∑ F Here, R is the vector sum of all forces acting on the beam and F denotes any individual force. Write the expression to calculate ∑ F . ∑ F = F A + F B Here, F A is the force applied at end A and F B is the force applied at end B. Rewrite the expression for R by substituting the above relation for ∑ F . R = F A + F B Write the expression to calculate the couple part of force couple system. M A R = ∑ ( r × F ) Here, M A R is the moment resultant of beam about point A and r is the length of beam which lies perpendicular to forces. Write the expression to calculate ∑ ( r × F ) . ∑ ( r × F ) = M A + M B + ( 0 m × F A ) + ( r × F B ) = M A + M B + ( r × F B ) Here, M A is the moment at end A and M B is the moment at end B. Rewrite the expression for M A R by substituting the above relation. M A R = M A + M B + ( r × F B ) Calculate the resultant force ( R ) . Substitute − 200 N for F A and − 400 N for F B . R = − 200 N+ ( − 400 N ) = − 600 N Calculate the moment resultant of beam about point A ( M A R ) . Substitute − 400 N ⋅ m for M A , 2800 N ⋅ m for M B , − 400 N for F B and 4 m for r . M A R = − 400 N ⋅ m + 2800 N ⋅ m+ ( 4 m × − 400 N ) = 800 N ⋅ m Calculate the force couple system of each loading given in Fig. P3.101. Refer figure 3.101(a). Calculate the resultant force ( R ) . Substitute − 400 N for F A and − 200 N for F B . R = − 400 N+ ( − 200 N ) = − 600 N Calculate the moment resultant of beam about point A ( M A R ) . Substitute 0 N ⋅ m for M A , 1800 N ⋅ m for M B , − 400 N for F B and 4 m for r . M A R = 0 N ⋅ m + 1800 N ⋅ m+ ( 4 m × − 200 N ) = 1000 N ⋅ m Refer figure 3.101(b). Calculate the resultant force ( R ) . Substitute − 600 N for F A and 0 N for F B . R = − 600 N+ 0 N = − 600 N Calculate the moment resultant of beam about point A ( M A R ) . Substitute 0 N ⋅ m for M A , − 900 N ⋅ m for M B , 0 N for F B and 4 m for r . M A R = 0 N ⋅ m + ( − 900 N ⋅ m ) + ( 4 m × 0 N ) = − 900 N ⋅ m Refer figure 3.101(c). Calculate the resultant force ( R ) . Substitute 300 N for F A and − 900 N for F B . R = 300 N+ ( − 600 N ) = − 6 00 N Calculate the moment resultant of beam about point A ( M A R ) . Substitute 0 N ⋅ m for M A , 4500 N ⋅ m for M B , − 900 N for F B and 4 m for r . M A R = 0 N ⋅ m + 4500 N ⋅ m+ ( 4 m × − 900 N ) = 900 N ⋅ m Refer figure 3.101(d). Calculate the resultant force ( R ) . Substitute − 400 N for F A and 800 N for F B . R = − 400 N+ 800 N =400 N Calculate the moment resultant of beam about point A ( M A R )

12th Edition

ISBN: 8220106797044

Author: BEER

Publisher: YUZU

See similar textbooks

Videos

Question

Chapter 3.4, Problem 3.102P

(a)

To determine

Identify the equivalent loading of figure P3.102 from any of the loadings from figure P3.101.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 3.4, Problem 3.101P

Chapter 3.4, Problem 3.103P

Students have asked these similar questions

Auto Controls Design a proportional derivitivecontroller for a plant orsystemthat satisfies the following specifications : 1. is steady-state error is less than 2 % for a ramp input. 2.) Damping ratio (zeta) is greater than 0.7have determined the 3. Once youvalue of kp and kd, then plotthe response of the compensated(with controller) and uncompensated( without the controller, only the plantsystem using MATLAB.

Auto Controls (a) Refer to the above figure .What kind of controller is it ? (b) simplify the block diagramto derive the closed loop transfer function of the system. (C) What are the assumptions thatare needed to make to findthe controller gain ? What arethe value of Kp , Ti and Td ?

Auto Controls Design a PID controller for thefollowing system so that the modified system satisfies the followingspecifications : 1. settling time ,ts = 1.96 s and % Overshoot Mp = 70.7 % Assume a non-dominant pole at s = -15 to solve the problem The plot the compensated andThen plot the uncompensated system in MATLAB. what can you see from the plot ? what is your observation ?

Chapter 3 Solutions

EBK VECTOR MECHANICS FOR ENGINEERS: STA

Ch. 3.1 - A foot valve for a pneumatic system is hinged at...Ch. 3.1 - 3.2A foot valve for a pneumatic system is hinged...Ch. 3.1 - It is known that a vertical force of 200 lb is...Ch. 3.1 - A 300-N force is applied at A as shown. Determine...Ch. 3.1 - A 300-N force is applied at A as shown. Determine...Ch. 3.1 - An 8-lb force P is applied to a shift lever....Ch. 3.1 - Prob. 3.7P Ch. 3.1 - An 11-lb force P is applied to a shift lever. The...Ch. 3.1 - Rod AB is held in place by the cord AC. Knowing...Ch. 3.1 - Rod AB is held in place by the cord AC. Knowing...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Identify the equivalent loading of figure P3.102 from any of the loadings from figure P3.101.

Solution Summary: The author identifies the equivalent loading of Figure P3.102 from any of the loadings from figure P3.101. Write the expression to calculate the force part of force couple system.

Videos

Identify the equivalent loading of figure P3.102 from any of the loadings from figure P3.101.

Want to see the full answer?

Chapter 3 Solutions