
Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 33, Problem 29R
Which nickel alloy would be best for joining the following:
a. poorly fitting joints
b. honeycomb structures
c. jet engine parts
d. corrosive applications
Expert Solution & Answer

Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Question 6
What kind of problem would arise if components of the strain tensor were defined
as v
Double counting of the normal strains.
Strain discontinuity.
Rotation would lead to a shear strain.
Double counting of the shear strains.
please show steps, thanks
You design a pin joint. The pin is made of a material with the yield strength of 325
MPa and ultimate strength of 500 MPa. The maximum allowed stress in service is
expressed as a tensor
0
100 0
σ
100
0
0 MPa
0
0
Evaluate the safety factor SF for stress in this design.
Write answer unitless rounding to 2 decimal places and enter decimals even if those
are zeros.
Chapter 33 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 33 - Explain the difference between brazing and...Ch. 33 - How does capillary action separate brazing from...Ch. 33 - Why can brazing be both a permanent and a...Ch. 33 - Why is it less likely that a part would be damaged...Ch. 33 - What is the effect of joint spacing on joint...Ch. 33 - Why are braze joints subject to fatigue failure?Ch. 33 - Do all braze joints resist corrosion? Give an...Ch. 33 - What are the three primary functions that a flux...Ch. 33 - In what forms are fluxes available?Ch. 33 - How can liquid fluxes be delivered to the joint...
Ch. 33 - How do fluxes react with the base metal?Ch. 33 - How are brazing and soldering methods grouped?Ch. 33 - What are the advantages of torch soldering?Ch. 33 - What are the advantages of furnace brazing?Ch. 33 - How does the induction brazing method heat the...Ch. 33 - What soldering process can be used to join parts...Ch. 33 - What brazing or soldering process uses a machine...Ch. 33 - What is a metal alloy?Ch. 33 - Why must parts not be moved as they cool through...Ch. 33 - Why must you not use tin-lead solders on water...Ch. 33 - Using Table 33-3, determine the approximate...Ch. 33 - What is a major use of tin-antimony solder?Ch. 33 - What solder alloy can retain its strength at...Ch. 33 - Why do brazing alloys use letters such as CuZn to...Ch. 33 - What is the white smoke that can be given off from...Ch. 33 - Which copper-zinc brazing alloy could be used to...Ch. 33 - Why should copper-phosphorus not be used on...Ch. 33 - Silver-copper alloys can be used to join which...Ch. 33 - Which nickel alloy would be best for joining the...Ch. 33 - Why does BCu-2 brazing alloy use an organic...Ch. 33 - Using Table 33-6, determine the ideal joint...Ch. 33 - What indicates that you have overheated the solder...Ch. 33 - How can the size of a braze bead be controlled?Ch. 33 - Why is brazing a better process than welding to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 2. A single crystal of aluminum is oriented for a tensile test such that its slip plane normal makes an angle of 28.1° with the tensile axis. Three possible slip directions make angles of 62.4°, 72.0°, and 81.1° with the same tensile axis. (a) Which of these three slip directions is most favored? (b) If plastic deformation begins at a tensile stress of σ x = 1.95 MPa (280 psi), determine the critical resolved shear stress for aluminium. (c) If this single crystalspecimen is loaded under the new stress state: σ x =1.2 MPa σ y = -0.8 MPa, and τ xy = 0.6 MPa, howmuch is the resolve the shear stress along the most favored slip direction?arrow_forwardPlease explain how to do each part and tell me if my drawing is correct. thank youarrow_forward4. Determine which of the following flow fields represent a possible incompressible flow? (a) u= x²+2y+z; v=x-2y+z;w= -2xy + y² + 2z a (b) V=U cose U coso 1 (9) [1-9] Usino |1 (4)] [+] V=-Usin 1+1arrow_forward
- 3. Determine the flow rate through the pipe line show in the figure in ft³/s, and determine the pressures at A and C, in psi. 5' B C 12° 20' D 6"d 2nd- Water Aarrow_forward5. A flow is field given by V = x²₁³+xy, and determine 3 ·y³j- (a) Whether this is a one, two- or three-dimensional flow (b) Whether it is a possible incompressible flow (c) Determine the acceleration of a fluid particle at the location (X,Y,Z)=(1,2,3) (d) Whether the flow is rotational or irrotational flow?arrow_forwardSolve this problem and show all of the workarrow_forward
- Solve this problem and show all of the workarrow_forwarddraw the pneumatic circuit to operate a double-acting cylinder with: 1. Extension: Any of two manual conditions plus cylinder fully retracted, → Extension has both meter-in and meter-out, 2. Retraction: one manual conditions plus cylinder fully extended, → Retraction is very fast using quick exhaust valve.arrow_forwardCorrect answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you. Expert solution plsarrow_forward
- Correct answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you.arrow_forwardCorrect answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you.arrow_forwardCorrect answer is written below. Detailed and complete solution only with fbd. I will upvote, thank you.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning

Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning

Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License