Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 33, Problem 1RQ
A hydronic heating system uses ______to move heat around in the system.
Expert Solution & Answer
To determine
The media used by hydronic system to move heat around in the system.
Answer to Problem 1RQ
Hydronic heating system uses water or steam to move heat around in the system.
Explanation of Solution
Hydronic system is the system in which the transfer of heat from one place to another place is done by the means of water or steam. The hydronic system consists of pipes which carry hot water to warm the space and can carry cool water to absorb heat from the space.
Hydronic heating system contains a heating device, expansion tank, pump and a network of pipe. The heating device can be a boiler which boils the water and add some heat to increase its temperature.
The hot water is pumped into the pipe network by the means of a pumping device. The hydronic system is a closed system so there is an expansion tank where water expands and can cool for another cycle.
Conclusion:
Thus, hydronic heating system use water or steam to move the heat around in the system.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Q2. Determine the safety factors for the bracket rod shown in Figure 2 based on both the
distortion-energy theory and the maximum shear theory and compare them.
Given: The material is 2024-T4 aluminum with a yield strength of 47 000 psi.
The rod length /= 6 in. and arm a = 8 in. The rod outside diameter od 1.5 in., id = 1 in, h=2 in.,
t=0.5 in., Load F= 1000 lb.
Assumptions: The load is static and the assembly is at room temperature. Consider
shear due to transverse loading as well as other stresses. (Note: solve in SI units)
wall
tube
Figure 2
arm
The question has been set up with all the cuts needed to accurately derive expressions for V(x) and M(x). Using the cuts free body diagrams set up below, derive expressions for V(x) and M(x). If you use the method of cuts then validate your answers using calculus or vice versa.
It is required to treat 130 kmol/hr of chloroform-air feed gas mixture that contains
12% chloroform. It is required to remove 93% of chloroform using 150 kmol/hr of
solvent that contains 99.6% water and 0.4% chloroform. The cross sectional area of the
column is 0.8 m². Calculate the column height using the following data; kx'.a = 1.35
(kmol/m³.s (Ax)), and ky'.a = 0.06 (kmol/m³.s (Ay)), kx/ky = 1.35, and the equilibrium
data are:
X 0 0.0133 0.033
y 0 0.01 0.0266
0.049 0.064 0.0747 0.0933 0.1053
0.0433 0.06 0.0733
0.111
0.1
0.12
0.14
Chapter 33 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 33 - A hydronic heating system uses ______to move heat...Ch. 33 - Describe a zone in a hydronic heating system.Ch. 33 - Name four sources of heat commonly used for...Ch. 33 - Give three reasons that air is detrimental to a...Ch. 33 - Explain the difference between a wet-base and a...Ch. 33 - Where is air vented from a hydronic heating...Ch. 33 - The "point of no pressure change" is located at...Ch. 33 - The purpose of a limit control in a boiler is to...Ch. 33 - The device that relieves the pressure in a boiler...Ch. 33 - Describe the function of a low-water cutoff.
Ch. 33 - The relief valve setting for a typical...Ch. 33 - Describe how an air cushion tank functions in a...Ch. 33 - True or False: City water does not contain air.Ch. 33 - State two ways that air can get into a hydronic...Ch. 33 - The most common type of pump used for hydronic...Ch. 33 - Another term for pump pressure is feet of _______.Ch. 33 - Two types of zone control valves are the _____and...Ch. 33 - Why must expansion be considered when sizing...Ch. 33 - How is expansion in hot water pipes handled?Ch. 33 - Sketch the following systems: one pipe, two-pipe...Ch. 33 - Describe the advantage of a two-pipe...Ch. 33 - The pressure differential bypass valve is most...Ch. 33 - What is the heat output, in Btu/h, of a terminal...Ch. 33 - In a primary-secondary pumping arrangement, the...Ch. 33 - The temperature of the water at the outlet of a...Ch. 33 - A tankless water-heating system gets its heat from...Ch. 33 - How much of the sun's energy actually reaches the...Ch. 33 - The varying intensity of the sun's energy that...Ch. 33 - Drain-down systems would best be used in which...Ch. 33 - Why are solar systems intended to be used as a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- ४ B: Find the numerical solution for the 2D equation below and calculate the temperature values for each grid point shown in Fig. 2 (show all steps). (Do only one trail using following initial values and show the final matrix) [T1] T₂ T3 [T] 1 = [0] 0 0 d dx dx) (ka)+4(ka) = dy -20xy, k = 1 + 0.3 T ge L=3cm, 4x= Ay B.Cs.: at x=0=LT=0°C at y=0-L T=10°C Fig. (2)arrow_forward: +0 العنوان use only Two rods fins) having same dimensions, one made orass (k = 85 Wm K) and the mer of copper (k = 375 W/m K), having of their ends inserted into a furna. At a section 10.5 cm a way from furnace, the temperature of brass rod 120 Find the distance at which the ame temperature would be reached in the per rod ? both ends are ex osed to the same environment. ns 2.05 ۲/۱ ostrararrow_forwardFor the beam show below, draw A.F.D, S.F.D, B.M.D 6 kN/m 1 M B. 3 M Marrow_forward
- 1. Two long rods of the same diameter-one made of brass (k=85w/m.k) and the other made of copper (k=375 w/m.k) have one of their ends inserted into a furnace (as shown in the following figure). Both rods are exposed to the same environment. At a distance of 105 mm from the furnace, the temperature of the brass rod is 120°C. At what distance from the furnace will the same temperature be reached in the copper rod? Furnace 105 mm T₁ Brass rod ⑪ h Too- x2- Ti Copper rodarrow_forward: +0 العنوان use only Two rods fins) having same dimensions, one made orass (k = 85 Wm K) and the mer of copper (k = 375 W/m K), having of their ends inserted into a furna. At a section 10.5 cm a way from furnace, the temperature of brass rod 120 Find the distance at which the ame temperature would be reached in the per rod ? both ends are ex osed to the same environment. ns 2.05 ۲/۱ ostrararrow_forwardمشر on ۲/۱ Two rods (fins) having same dimensions, one made of brass(k=85 m K) and the other of copper (k = 375 W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm a way from the furnace, the temperature brass rod 120°C. Find the distance at which the same temperature would be reached in the copper rod ? both ends are exposed to the same environment. 22.05 ofthearrow_forward
- The composite wall of oven with A= 1m² as in Fig.1 consists of three materials, two of with kA = 20 W/m K and kc = 50 W/m K with thickness, LA=0.3 m, L= 0.15 m and Lc 0.15 m. The inner surface temperature T1=900 K and the outer surface temperature T4 300 K, and an oven air temperature of To=1100 K, h=25 W/m². K. Determine kɛ and the temperatures T2 and T3 also draw the thermal resistance networkarrow_forwardTwo rods (fins) having same dimensions, one made of brass (k = 85 Wm K) and the other of copper (k = 375 W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm a way from the furnace, the temperature of brass rod 120°C. Find the distance at which the same temperature would be reached in the copper rod ? both ends are exposed to the same environment. Ans 22.05arrow_forwardA long wire (k-8 W/m °C.) with ro 5 mm and surface temperature Ts=180°C as shown in Fig.2. Heat is generated in the wire uniformly at a rate of 5 x107 W/m³. If the energy equation is given by: d 11(77) + - =0 k r dr dr Derive an expression for T(r) and determine the temperature at the center of the wire and at r=2 mm. Air Th T KA LA T2 T3 T Fig.1 KB kc 180°C Го Fig.2arrow_forward
- B: Find the numerical solution for the 2D equation below and calculate the temperature values for each grid point shown in Fig. 2 (show all steps). (Do only one trail using following initial values and show the final matrix) T₂ 0 T3 0 I need a real solution, not artificial intelligence locarrow_forwardCan I solve this problem by calculating the initial kinetic energy with respect to G instead of A.arrow_forwardB: Find the numerical solution for the 2D equation below and calculate the temperature values for each grid point shown in Fig. 2 (show all steps). (Do only one trail using following initial values and show the final matrix) T₂ 0 T3 0 locarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license